Bedienungsanleitung Futaba 12Z (Seite 123 von 127) (Englisch)

29029

123

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

123

<Data>

EXP1/EXP2 curve adjustment

(EXP1 curve)

8VLQJWKH(;3FXUYHLVHIIHFWLYHLQ

smoothing starting of the ailerons, elevator,

rudder, etc.

(EXP2 curve)

8VLQJWKH(;3FXUYHLVHIIHFWLYHLQHQJLQH

rise and other engine control.

The curve left and right rates ([RATE A],

>5$7(%@DQG(;3FXUYHUDWH>(;3$@>(;3

%@FDQEHDGMXVWHGLQGLYLGXDOO\>(;3@IRU

(;3

The curve can also be offset horizontally

([OFFSET]) in the vertical direction.

[Rate setting]

1. Use the cursor lever to move the cursor

(reverse-video) to the [RATE A], [RATE B],

[EXP A], or [EXP B] setting item.

2. Set the rate by turning the data input dial

to the left or right.

Initial value: +100.0% (rate)/+0.0% (EXP

rate)

Adjustment range: -200.0~+200.0%

(rate)/-100.0~+100.0% (EXP rate)

(When the enter button is pushed for 1 second, the rate is

reset to the initial value.)

[Offsetting the curve horizontally in the

vertical direction]

1. Use the cursor lever to move the cursor

(reverse-video) to the [OFFSET] setting

item.

2. Move the curve in the vertical direction

by turning the data input dial to the left or

right.

Initial value: +0.0%

975FXUYHDGMXVWPHQW

975FXUYH

When this curve is used, when the operating

rudder angle is large such as with acrobatic

models, switching from normal flight to

acrobatic rudder angle is performed without

switch operation.

The curve left and right rates ([RATE A],

[RATE B]) can be adjusted individually. The

curve can also be offset horizontally ([OFFSET])

in the vertical direction.

The VTR curve point position ([P.POS A],

[P.POS B], and rate ([P.RATE A], [P.RATE B])

can be adjusted individually.

[Rate setting]

1. Use the cursor lever to move the cursor

(reverse-video) to the [RATE A] or [RATE B]

setting item.

2. Set the rate by turning the data input dial

to the left or right.

Initial value: +100.0%

Adjustment range: -200.0~+200.0%

(When the enter button is pushed for 1 second, the rate is

reset to the initial value.)

[VTR curve point setting]

1. Use the cursor lever to move the cursor

(reverse-video) to the [P.POS A], [P.POS B],

[P.RATE A], or [P.RATE B] setting item.

2. Set the rate by turning the data input dial

to the left or right.

Initial value: +50% ([P.POS A], [P.POS

B])/+100.0% ([P.RATE A], [P.RATE B])

Adjustment range: +0.0~+100.0%

(When the enter button is pressed for 1 second, the rate is

reset to the initial value.)

*When [P.POS A] or P.POS B] is made large, the curve

point moves to the outside. When [P.RATE A] or [P.RATE

B] is set to +100%, the curve becomes a straight line.

[Offsetting the curve horizontally in the

vertical direction]

1. Use the cursor lever to move the cursor

(reverse-video) to the [OFFSET] setting

item.

Move the curve in the vertical direction by

turning the data input dial to the left or right.

Initial value: +0.0%

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 12Z Seite 123

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info