Bedienungsanleitung Futaba 14MZ (Seite 63 von 127) (Englisch)

29031

Zoom out

Zoom in

Vorherige Seite

1/127

Nächste Seite

●Return to Linkage Menu

● Touch the [Fail Safe] button in the Linkage

Menu to call the setup screen shown below.

Fail Safe

Sets the servos operating position when transmitter signals can no longer be received or

when the receiver battery voltage drops.

(The display screen is an example. The screen depends on the model type.)

The Failsafe function may be used to set up positions

that the servos move to in the case of radio interference.

This function only works with G3 or PCM receivers

(FM receivers do not have failsafe capability).

When the receiver battery voltage drops, the servo

can be moved to a preset position. (Battery fail safe

function) A battery fail safe function reset switch can be

set. (Initial setting: Throttle stick maximum slow side)

You may set either of two positions for each

channel: Hold, where the servo maintains its last

commanded position, or Failsafe, where each servo

moves to a predetermined position. You may choose

either mode for each channel.

The T14MZ system also provides you with

an advanced battery monitoring function that

warns you when the receiver battery has only a

little power remaining. In this case, each servo is

moved to the deﬁ ned failsafe position. The battery

Fail safe setting procedure

Decide which channels you want to go to preset

positions, and which ones you want to maintain

their last commanded position. To select the failsafe

mode you wish to set, use the F/S button. This

button toggles between the two modes. (Hold, F/S)

F/S mode setting:

1. Touch the F/S button of the channel you

want to set, and set that channel to the [F/S]

mode.

2. Hold the corresponding stick, control, slider,

or other control in the position you want

the servo to move to when the fail safe

function is activated, and touch the F/S

position button. That position is displayed in

percentage.

*When you want to return that channel to the Hold mode,

touch the [F/S] button again.

Battery fail safe setting procedure

To select the B.F/S mode, touch the [B.F/S]

button. Each time the button is touched, it toggles

failsafe may be released by operating a predeﬁ ned

control on the transmitter (default is throttle),

do not continue to fly, land as soon as possible.

Remember, if the predefined control suddenly

moves to a position you did not command, land at

once and check your receiver battery.

Deﬁ nes servo position when signals are lost and

when receiver battery voltage becomes low.

WARNING

For safety, always set the fail safe functions.

●Especially set the throttle channel fail safe function so that

the servo moves to the maximum slow side for airplanes and

to the slow side from the hovering position for helicopters.

Crashing of the model at full high when normal radio waves

cannot be received due to interference, etc., is very dangerous.

●If fail safe is reset by throttle stick, it may be mistaken for an

engine malfunction and will be reset at throttle slow and the model

will continue to ﬂ y. If you have any doubts, immediately land.

between [OFF] and [B.F/S].

B.F/S setting:

1. Touch the [B.F/S] button of the desired

channel to set it to the B.F/S mode.

2. Hold the corresponding stick, VR, slider, or other

control in the position you want the servo to

move to when the battery fail safe function is

activated, and touch the F/S position button.

This position is displayed in percentage.

*When you want to return that channel to OFF, touch the [B.F/

S] button again.

Battery Failsafe Release Function

This function releases the predefined control

from it's held position after indicating that your

receiver battery is low.

1. Enter the control setting screen by touching

the Battery F/S Release button. Now, you may

choose that moving the throttle resets the

condition, or select another stick or switch

deactivates it. To set a desired throttle release

position, move the throttle stick to the point at

which you wish the B.F/S to be released.

●To <Switch>

screen

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 14MZ Seite 63

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info