747923
21
Zoom out
Zoom in
Vorherige Seite
1/30
Nächste Seite
22
Assembly / Adjustment
Transmitter Set-Up Procedures
*When making these settings adjustments, do so with the motor disconnected or
the engine not running.
NEUTRAL, HIGH, AND BRAKE MAX POINT SETTINGS
Before setting each point, set the transmitter throttle channel trim to neutral.
Tur n on the power in transmitter amp order.
1
2
Transmitter throttle operation
Neutral state
Press the pushbutton switch.
(0.5 secs or longer)
(Confirmation beep sounds)
Continuous single blink
MC231CR
(Pushbutton switch operation) (Checker LED)
Full high
Full brake
Neutral point
setting
3
Full high state
Press the pushbutton switch.
(Confirmation beep sounds)
Continuous double blink
Continuous rapid blink
High point
setting
4
Full brake state
Press the pushbutton switch.
(Confirmation beep sounds.)
If the LED goes out,
setting is complete.
Brake MAX
point setting
* Since the data is read at the end of setting of all points, the points cannot be set independently.
* If the amp power was turned off during setting, the setting points cannot be memorized. (The previous settings are retained.)
* The confirmation beep sounds only when the motor was connected.
If the LED does not go off
but blinks rapidly, setting
was not performed
normally. Repeat setting
from "Neutral point
setting".
Servo Horn Installation Instructions
1
Connect the receiver, ser vos, and other components and
then tur n on the power switches to transmitter and receiver.
*Both servos will move to the neutral position.
2
At this time install the ser vo horn in the manner descr ibed in
the instruction manual provided with the model this system
will be used in.
Reversing The Servo Operation Direction
Should the ser vo operate in
the opposite direction required
for your application, reverse
the direction with the ser vo
reversing.
E.S.C. MC231CR / MC331CR
Throttle Servo
Reversing
Steering Servo
Reversing
NOR: Normal NOR: Normal
REV: Reverse REV: Reverse
21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Futaba 2HR wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info