Bedienungsanleitung Futaba 2PKA (Seite 5 von 8) (Englisch)

28967

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

• A common power supply regulator and diode may also be supplied with the speed controller, depending on the vehicle kit. Since

they cause a voltage drop, always remove them.

• Set the transmitter power switch to ON, then set the receiver power

switch to ON. The servos stop near the neutral position. Operate the

transmitter sticks and check if each servo faithfully follows opera-

tion of the sticks.

• Connect the pushrod to each servo horn, then check if the direc-

tion of travel of each servo matches the transmitter operation.

• Operate each servo over its full travel and check if the pushrod binds

too

loose.

Applying

unreasonable force

the

servo

horn

will

adversely affect the servo and quickly drain the battery. Be especial-

ly careful when using 8.4V.

•

Always make the

full

stroke

(including

trim)

the

servo

horns

somewhat larger

than

the

full

travel.

Adjust

the

servo

horns

that

they move smoothly even when the trim lever and stick are operated

simultaneously in the same direction.

• Be alert for noise.

Always solder a noise killing capacitor to the running motor. If

metal pans touch each other due to vibration, noise will be generat-

ed and cause the receiver servos to operate erroneously. We recom-

mend the use of noiseless parts.

• Even though the receiver antenna wire is long, do not cut or bundle

it. The range of the radiowaves will be shortened.

Receiver antenna

wire

— Wood screw

ten

-Rubber bushing

-Gromet

Fig.

• Install the servos firmly. Install

the servo to the servo tray as

shown in the figure. In other

cases, install the servo as des-

cribed in the model manufac-

turer's manual.

• A spare horn is provided. Use it as required.

• Wrap the receiver in sponge rubber and wrap rubber bands around

the sponge rubber. Mount the receiver so it is not exposed to vibra-

tion, does not touch the frame, and does not move.

• When the receiver is installed on a board or used where it may be

splashed with mud and water, place it in a plastic bag, etc. and

wrap a rubber band around the open end of the bag to waterproof

and dustproof the receiver. After use, remove the receiver from the

bag to prevent condensation.

• Use the rubber bands wrapped around the receiver to hold the

servo and switch leads.

• After mounting is complete, recheck each part, then check the

transmitting range by making the transmitter antenna as short as

possible and extending the receiver antenna fully and operating the

set from a distance of 20m to 30m. The movement of each servo

should follow the movement of the transmitter sticks.

• The crystal can be changed from the outside of the receiver case.

Always use a Futaba transmitter and receiver crystal pair as the

replacement crystals.

CONVERSION TO NICAD SYSTEM

FP-2PKA ONLY

To use a nicad battery with this set, modify

the set with the optional PBPK-11 (2PKA

nicad battery conversion set).

(1) Remove the battery cover and discon-

nect the nine contacts with needle nosed

pliers at shown in Fig. 15. Then install

the transmitter NT-8LP nicad battery

and install the

battery cover.

Fig. 15

Transmitter NT-8LP

nicad battery.

(2) Charging and how to use

(a) Connect the power plug of the FBC-8B

(4) battery charger to the transmitter

charging connector. Connect the 3PC red

male connector to the receiver and servo

NR-4H nicad battery. Plug the battery

charger into a 120 VAC outlet as shown

Fig.

16.

(b) Normally recharge the battery for about

15 hours. If the battery has not been

used for some time or is new, discharge

and recharge it 2 or 3 times before use.

time, its capacity will decrease and the

life of the battery will be shortened.

After use, recharge the battery before

storing it.

(d) Always recharge the battery before use.

(e) A fully charged battery can be used for

about two hours at 10 minutes/flight.

Notes: FBC-8B (4)

(1) First, connect to TX Nicd and red lamp goes on.

(2) Then, connect to RX Nicd after connecting, L,E,D, changes color from red to greenish

red (orange) which indicates that both TX and RX Nicds are being charged.

(3) In case of separate charging, L,E,D, color will be: RX Nicd — Green

TX Nicd - Red

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 2PKA Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info