Bedienungsanleitung Futaba 2PL (Seite 12 von 22) (Englisch)

28971

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

Assembly / Adjustment

Install electronic speed control heat sinks as well as other components that conduct

electricity so they can not come in contact with aluminum, carbon fiber or other mate-

rials that conduct electricity.

If, for example, the speed control came loose while the model was running and

touched an aluminum chassis, a short circuit may occur that would cause irreparable

damage to the system as well as loss of control.

Installation Note

Noise suppression capacitors should be installed on almost all motors.

If the proper capacitors are not installed, high frequency noise will reduce range and

cause loss of control along with various other problems.

Installation Note

Inspect all linkage installations and any point where metal could come in contact with

other metal parts. Make sure these parts do not touch other metal parts under vibra-

tion.

Should a linkage or other metal parts come in contact with other metal parts under

vibration, the high frequency noise generated by this contact will cause interference

and possible loss of control.

Caution

Disassembly Prohibited

Do Not disassemble any part of this system that is not specified in the instruction

manual.

Futaba will not be responsible for any damage due to improper disassembly of any

part of the radio control system.

Prohibited

The receiver antenna may seem long. Do not cut or alter from the original length.

If the receiver antenna length is altered, the receiver will be adversely effected. The

receiver will become considerably more susceptible to interference and high fre-

quency noise which will result in loss of range and control.

Installation Note

(Electric Cars and Boats)

Isolate the receiver from vibration by attaching to the chassis or mounting plate with

thick double sided tape.

(Gas Powered Cars and Boats)

Isolate the receiver from vibration by wrapping it in foam rubber or similar type cush-

ioning material. Protect the unit from water damage by placing it in a plastic bag or

waterproof radio box.

The receiver contains precision electronic parts. These parts are vulnerable to vibra-

tion and shock. Any contact with moisture (water or condensation) may cause receiver

malfunction and loss of control.

Installation Note

Keep all devises that omit high frequency noise, such as motors, batteries, and wiring

that handles heavy current loads, at least 1/2 inch away from the receiver and the

receiver antenna.

High frequency noise will cause a decrease in operating range and could cause loss of

control.

Use genuine Futaba parts only.

Use only genuine Futaba crystal sets as specified in this instruction manual.

The use of other than Futaba crystal sets will result in decrease of range as well as

loss of control. There are separate crystals for the Transmitter and Receiver. There

are also crystal sets for AM, FM and Dual Conversion FM. Use only single conversion

AM crystal sets with this system.

Changing crystals in 72-75 MHz transmitter is illegal. However, 27 MHz is allowable.

(For U.S.A.)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 2PL Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info