Bedienungsanleitung Futaba 3PJ_super (Seite 28 von 110) (Englisch)

28975

Zoom out

Zoom in

Vorherige Seite

1/110

Nächste Seite

Installation

Installation Safety Precautions

Warning

Connector Connections

Be sure the receiver, servo, crystal

and connectors are fully and firmly

connected.

If vibration from the model cause a connector to work

loose while the model is in operation. You may lose

control .

Electronic speed control

Install the heat sinks where they will

not come in contact with aluminum,

carbon fiber or other parts that con-

duct electricity.

If the FET Amp (Electronic speed control) heat sinks

touch other materials that conduct electricity a short

circuit could occur. This could result in loss of control

and damage to the system.

Receiver Vibration Damping and

Waterproofing

(Car)

Dampen the vibration to the receiver

by mounting to the chassis or mount-

ing plate with thick double sided tape

in electric powered models. In gas

powered models wrap the receiver in

foam and mount it where the vibration

is the least prevalent.

(Boat)

Dampen the vibration to the receiver

by wrapping it in foam. Waterproof by

placing it in plastic bag or watertight

radio box in model.

If the receiver is subjected to strong vibration or shock

erratic or loss of control may occur. If any moisture

comes in contact the receiver and servos you may

expertise the same result as well as damage to the

system.

Receiver Antenna

Do not cut or bundle the receiver an-

tenna

Do not bundle the receiver antenna

together with the servo lead wires

Keep the receiver antenna at least 1

inch away from the motor and battery

and wires that handle heavy current

loads..

Cutting, bundling or routing the receiver antenna near

any devise that produce noise will reduce the operat-

ing range of the system and result in loss of control.

*Also route the receiver antenna away from metal,

carbon fiber and other parts that conduct electric-

ity. These parts can transmit high frequency noise.

Servo Throw

Operate each servo over its full stroke

and be sure the linkage does not bind

or is loose.

The continuous application of unreasonable force to a

servo may cause damage and excessive battery

drain.

Servo Installation

When you install the servos always

use the rubber grommets provided in

servo hardware bags. Mount the ser-

vos so they do not directly come in

contact with the mount.

If the servo case comes in direct contact with the

mount vibration will be directly transmitted to the

servo.

If this condition continues for a long time the servo

may be damaged and control will be lost.

Motor Noise Suppression

Always install capacitors to suppress

noise when electric motors are used.

If capacitors are not properly installed you could ex-

perience erratic operation and reduced range as well

as loss of control.

Other Noise Suppression Methods

Be sure there are no metal parts in

your model which under vibration can

come in contact with other metal

parts.

Metal to metal contacts under vibration will omit a high

frequency noise that will effect the receivers perfor-

mance. You could experience erratic operation and

reduced range as well as loss of control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 3PJ_super Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info