5
•
Transmitter, including RF module* (PK) and NiCd
battery pack NT8F700B (FUTM1462)
•
Receiver (R113iP or R203HRF)
•
110V wall charger FBC19B (USA)
•
Frequency Flag/Number set
•
Wheel position offset adapter (APA)
Transmitter T3PK (Pistol, 3 channels)
Operating system: FM/PCM1024/HRS
Transmitting frequency: 27, 75 MHz bands*
Modulation: FM/PPM, HRS-FM or PCM1024, switchable
Power supply: 9.6V NT8F700B NiCd battery
Current drain: 250 mA or less
Receiver R113iP ( PCM Single conversion, 3 channels)
Receiving frequency: 27, 75 MHz bands *‡
Intermediate freq.: 455 kHz
Power requirement: 4.8V or 6.0V NiCd battery or
4.8V (4 cells) alkaline
Current drain: 18 mA
Size: 1.69" x 1.13" x 0.63" [42.7 x 28.7 x 16.0mm]
Weight: 0.74oz [21g]
Receiver R203HF (3 channels, HRS single conversion)
Receiving frequency: 27, 75 MHz bands *‡
Intermediate frequency: 455kHz
Power requirement: 6.0V only (shared with servos)
Current drain: 14mA
Size: 1" x 1-1/2" x 9/16" [25.6 x 37.7 x 14.3mm]
Weight: .6oz [17g]
Always use only: “HRS” mode on transmitter
6V Digital Servo, including throttle
6V NiCd battery
* Transmitter band may only be changed by changing the
module. Receiver band cannot be changed. Band cannot be
changed by simply changing crystals.
‡ Only 27, 75MHz bands are legal for R/C ground use
in the North America.
Other bands are sold and used in other countries only.
CONTENTS AND TECHNICAL SPECIFICATIONS
(Specifications and ratings are subject to change without notice.)
Your system includes the following components:
The following additional accessories are available from your dealer. Refer to a Futaba catalog for more information:
•
CAMPac Memory module — the optional DP-16K CAMPac increases your model storage capability (to 20 models
from 10) and allows you to transfer programs to another 3PK transmitter. Note that data may not be transferred to/from
any other model of transmitter (3PJ, etc).
CAUTION - Insertion of a CAMPac containing data of a different transmitter type (ex: 3PJ) will result in
a complete CAMPac data reset and loss of all data.
•
Transmitter battery pack — the NT8F700B (700mAh) transmitter NiCd battery pack may be easily exchanged with a
fresh one to provide enough capacity for extended sessions.
•
Y-harnesses, servo extensions, etc – Genuine Futaba extensions and y-harnesses, including a Heavy-Duty version with
heavier gauge wire, are available to aid in your larger model and other installations.
•
5-cell (6.0V) receiver battery packs. All Futaba equipment (except that which is specifically labeled otherwise) is
designed to work with 4.8V (NiCd 4 cells) or 6.0V (NiCd 5 cells or alkaline 4 cells). Using a 6.0V pack increases the
current flow to the servos, which accelerates their rate of response and their torque. However, because of this faster
current draw, a 5-cell battery pack of the same mAh rating will last approximately ¾ the time of a 4-cell pack.
CAUTION - NOTE that HRS receivers require 6.0 volts and will not operate with 4.8V 4-cell packs.
•
Gyros – a variety of genuine Futaba gyros are available for your specialized model needs.
•
FailSafe: the FS1 FailSafe may be used with standard PPM/FM receivers to return throttle to idle in case of a loss of signal,
similar to the FailSafe function of PCM/HRS receivers. NOTE that HRS receivers can not operate with the FS1.
•
Battery Holder (Transmitter): This battery holder is necessary when using the transmitter with dry cell batteries. For a
description of how to install the battery holder to the transmitter, see “NiCd Replacement” on page 54.
•
DSC cord – allows setup and testing without transmitting. Requires DSC compatible receiver and DSC cord. With transmitter
and receiver off, plug cord into transmitter and then into receiver battery slot. Turn on receiver power. All programming and
setup may be done in this matter without transmitting. See glossary for a list of DSC-compatible receivers.
