28985
11
Zoom out
Zoom in
Vorherige Seite
1/20
Nächste Seite
Dual Rate Settings
To set the dual rates:
1. Enter the programming mode. Access the D/R screen with the MODE key.
2. Select the channel to be adjusted (1-aileron, 2-elevator) by pressing the SELECT key until the
desired channel number appears on the screen. Note: If a + or a appears next to the
number, you have pressed the SELECT key too many times and displayed the values for the
exponentials (explained later). Press the SELECT key to return to the dual rate values.
3. Place the dual rate switch in the desired position for the value you wish to change.
(Generally, pilots prefer to have the switch in the up position for the high rate, and in the
down position for the low rate.)
4. Change the dual rate value using the DATA INPUT lever until the desired control throw is
achieved. If you wish to change the control throw when the switch is in the other position as
well, flip the switch, then use the DATA INPUT lever to change the throw.
5. Repeat the procedure for the other dual rate (channel 2-elevator).
Exponential Settings
The exponentials are in the same function as the dual rates. (Pressing the MODE key will take you to the next function
which is End Point Adjustments). The same as dual rates, exposcan be set for both switch positions. Negative exponential
(-) decreases initial servo movement. Positive exponential (+) increases initial servo movement. The exponential curvemay
be set anywhere between -100% and +100%.
To set the exponentials:
1. Enter the programming mode, then select the channel (1-aileron, 2-elevator) you wish to set
by pressing the SELECT key. The active channel number will be displayed on the screen with
a + or a - next to the number (initially, the value will read – 0)
2. Position the dual rate switch where desired for the value you wish to change.
3. Enter the amount of exponential with the DATA INPUT lever. (As stated above, an exponential
value with a - in front of it makes the initial servo movement less, or softer.)
4. Flip the switch to the other position to enter the exponential value for that switch position.
5. Repeat for the settings on the other channel.
E.P.A End Point Adjustment
The E.P.A. function is designed to fine tune the servo throws in cases where changing the pushrod hookup will not achieve
the correct throw. The pushrods should first be connected to the servo arms and control horns so the correct, or near correct
control surface throw will be achieved. THEN the E.P.A.s may be used to make small changes in the servo throw until the
desired control throw is achieved. The control throws should be set up so that the end points are as near to 100% as
possible. If the E.P.A. values must be set below 70% or above 120% to get the desired
throw, you should strongly consider changing the pushrod connections so the values can
be set closer to 100%. (When the E.P.A. is set to 100% the maximum servo throw for
channels 1, 2, 3 & 4 is approximately 40° and approximately 55° for channels 5 & 6.)
To set the end points:
1. Enter the programming mode and use the MODE key to access the E.P.A screen. The channel
number being adjusted will appear on the screen and the % symbol will be flashing.
2. To change the RIGHT aileron throw move the aileron stick to the right, then push the
DATA INPUT lever up or down to change the value and the throw.
3. Move the stick to the left and use the DATA INPUT lever to change the LEFT aileron throw.
4. Use the SELECT key to display the other channels and set the other end points. Notice
that moving the stick (or switch or dial) from one end to the other changes the value
displayed and the position of the arrow for that end of the control input.
Note: Since changing the end pointswill also change the dual rates, the end points should be set prior to setting the dual
rates. If you set the dual rates first, and then go back and change the end points, the dual rate throws will also change.
11
11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Futaba 6EXA wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Futaba 6EXA

Futaba 6EXA Bedienungsanleitung - Französisch - 14 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info