Bedienungsanleitung Futaba 6EXAP (Seite 12 von 24) (Englisch)

28983

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

EXPO Exponential Settings

The

“exponentials” are in the same function as the dual rates. (Pressing the MODE key will take you to the next function

which is End Point Adjustments). The same as dual rates,

“expos” can be set for both switch positions. Negative exponential

(-) decreases initial servo movement. Positive exponential (+) increases initial servo movement. The exponential

“curve” may

be set anywhere between -100% and +100%.

To set the exponentials:

1. Enter the programming mode. Access the

“D/R

D/R

“ screen with the MODE key.

2. Access the

“EXPO

EXPO

“ screen with the SELECT key.

3. Select the channel (1-aileron, 2-elevator, 4-rudder) you wish to set by pressing the SELECT

key. The active channel number will be displayed on the screen Note: If a

“D/R“ will appear

on the screen, you have pressed the SELECT key too many times and displayed the values

for the D/R (dual rate values). Press the SELECT key to return to the exponentials.

4. Position the dual rate switch where desired for the value you wish to change.

5. Enter the amount of exponential with the DATA INPUT lever. (As stated above, an exponential value with a

“-” in front of it

makes the initial servo movement less, or

“softer.”)

6. Flip the switch to the other position to enter the exponential value for that switch position.

7. Repeat for the settings on the other channel.

EPA End Point Adjustment

Note:

Since changing the “end points” will also change the dual rates, the end points should be set prior to setting the dual

rates. If you set the dual rates first, and then go back and change the end points, the dual rate throws will also change.

The EPA function is designed to

“fine tune” the servo throws in cases where changing the pushrod hookup will not achieve the

correct throw. The pushrods should first be connected to the servo arms and control horns so the correct, or near correct control

surface throw will be achieved. THEN the EPAs may be used to make small changes in the servo throw until the desired control

throw is achieved. The control throws should be set up so that the

“end points” are as near to 100% as possible. If the EPA values

must be set below 70% or above 120% to get the desired throw, you should strongly consider changing the pushrod connections

so the values can be set closer to 100%. (When the EPA is set to 100% the maximum servo throw for channels 1, 2, 3 & 4 is

approximately 40

˚ and approximately 55 ˚ for channels 5 & 6.)

To set the end points:

1. Enter the programming mode and use the MODE key to access the “EPA

EPA

” screen. The

channel number being adjusted will the left side on the screen and the % symbol will be

flashing.

2. To change the RIGHT aileron throw move the aileron stick to the right, then push the DATA

INPUT lever up or down to change the value and the throw.

3. Move the stick to the left and use the DATA INPUT lever to change the LEFT aileron throw.

4. Use the SELECT key to display the other channels and set the other end points. Notice that

moving the stick (or switch or dial) from one end to the other changes the value displayed and

the position of the arrow for that

“end” of the control input.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6EXAP Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info