Bedienungsanleitung Futaba 6EXAP (Seite 20 von 24) (Englisch)

28983

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

OTHER 6EXAP FUNCTIONS

Trainer switch

To utilize the trainer function, the appropriate trainer cord (available separately) and a second Futaba transmitter (usually

provided by your flight instructor or R/C club) will be required. When two radios are connected with the trainer cord, they are

both capable of operating the model, but it's usually best for the instructor to hold the radio that has been setup for the plane

to be flown (as it is already programmed to fly the model). When the instructor holds the trainer switch on his radio, the student

will have control. When the instructor wishes to regain control he simply releases the switch. Then he will have immediate, full

control.

If connecting the 6EXAP to another 6EXAP with the small, square

“micro” trainer jack, use the “Micro to Micro” (MM-TC)

trainer cord (FUTM4415). If connecting the 6EXAP to Futaba radios with the larger, round,

“DIN” connector, use “Micro to

DIN” (MD-TC) trainer cord (FUTM4420). The T6EXAP transmitter may be connected to another T6EXAP, or any 4VF, 6VA

Skysport, T6EXA, FF6 - 9, or 9Z series transmitter.

To use the trainer cord:

1. It is best for the instructor to use the transmitter that is already set up for the model to be flown.

2. If the student's radio has PCM/PPM capability, set it to PPM.

3. If the student's radio has a plug-in RF module, remove the module.

4. Collapse the student's antenna and fully extend the instructor's antenna.

5. With the transmitters off, connect the trainer cord to both radios. (On the 6EXA the trainer

jack is in the center of the rear of the case.) Do not force the plug into the transmitter and

note that the plug is

“keyed” so it can go in only one way.

6. Turn on the instructor's transmitter. DO NOT

DO NOT

turn on the students transmitter it will automatically “power up,” but will not

transmit a signal. Set the servo reversing and trims of the student's radio to match that of the instructor's.

7. Turn on the receiver switch in the model. Depress the trainer switch on the instructor's radio. Use the student

’s radio to

operate the controls (ailerons, elevator, rudder, etc.) and observe how they respond. Make any adjustments necessary to

the student's transmitter to get the controls to respond correctly.

8. Check to see that the trims are in

“sync” by toggling the trainer switch back and forth a few times. The controls on the model

should remain stationary. If the controls do not remain stationary, this indicates that the trim settings on the student's radio

do not match those on the instructor's radio. Adjust the student's trims as necessary.

Note:

When the instructor initially depresses the trainer switch on his transmitter, there will be a one-second delay before the

student takes control. In most situations this momentary delay will go unnoticed.

Throttle-cut function

The throttle-cut function is intended to be used for shutting off the engine. The engine can be conveniently shut off by pressing

the "THR Cut" button. The throttle-cut feature prevents inadvertently shutting off of the engine when lowering the throttle stick

all the way (such as when coming in for a landing or taxiing). Throttle-cut works only when the throttle stick is down. To set up

throttle-cut, turn on the transmitter and receiver. Actuate the throttle-cut function by rapidly depressing, then releasing the

switch twice. Observe the momentary position of the carburetor barrel on the engine. It should be fully closed (thus shutting off

the engine). If necessary, use the throttle E.P.A. (channel 3) to fully close the carburetor barrel when the throttle-cut is

activated. Now use the throttle trim to open the carburetor barrel so the engine will idle at the desired R.P.M. when the throttle

stick is all the way down.

Optional Flap control lever (Option)

When the flaperon mixing function is activated, the optional flap control lever

flap control lever

can be used to set maximum flap deflection by

mechanically limiting the dial. This will prevent inadvertently retracting the flaps beyond their full, "up" position. To use the flap

control lever, turn the flap dial until the flaps are retracted (up). Place the flap control lever over the dial so that the arm is

contacting the transmitter case. This will limit rotation of the dial so the flaps cannot go up any farther.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6EXAP Seite 20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info