Bedienungsanleitung Futaba 6XA (Seite 39 von 64) (Englisch)

28989

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

ELVN — Elevon Mixing

The Elevon function should be used with delta wings, flying wings,

and other tailless aircraft whose layouts combine the aileron and elevator

functions, and requires one servo for each elevon. Connect the right

aileron to receiver CH1/AIL and the left aileron to CH2/ELE.

1CH

Aileron operation

Elevator operation

2CH

The amount of aileron and elevator response can be adjusted

independently. However, if you program in too much elevator or rudder

travel, the servos may reach their travel limits before full stick motion has

occurred. Therefore, you should keep the travel settings at 50% or below

and adjust the control linkages to get the travel you desire.

NOTE: The elevon, V-tail, and flaperon functions cannot be activated simultaneously.

The function activated last has priority.

Setting up elevon mixing

1. Use the up or down arrow keys to select the

ELVN

window.

2. Press the

CURSOR key three times to get to the activation setting. The INH

indicator will flash on and off.

3. Now press the (+) key to enable the elevon function. The display will

show a flashing ON.

4. Press the

CURSOR key once, to get to the aileron setting menu. A small

arrow is displayed over the numeral 1 (representing aileron master

channel), and the plus or minus sign above the large setting number will

blink on and off.

Move the aileron stick all the way to the right: the right elevon should move upwards, and

the left elevon should move downwards. If they move opposite to this, change the aileron

travel direction with the (+) and (–) keys. Note that this reverses the response at both elevon

servos (not just one as in the REV menu). If both servos move the same direction, reverse

the one that moves improperly in the REV menu.

5. Now you’ll input the amount of aileron travel by pressing the

CURSOR key once. Now the

percent sign will blink on and off, and you may adjust the amount of aileron travel with the

(+) and (–) keys. You may change the initial 50% setting to be anywhere between 0% and

100% (press the plus and minus keys together if you wish to reset to 50%).

6. Next: the elevator inputs. Press the

CURSOR key once. A small arrow

should appear over the numeral 2 in the screen (indicating elevator is the

master channel), and the sign in front of the large setting number will flash

on and off. Verify that when you pull back on the elevator stick, both the elevon servos

move upwards. If they move the incorrect direction, change the direction by pressing the (+)

or (–) key which changes the flashing sign displayed.

7. Now you’ll input the amount of elevator travel by pressing the

CURSOR key once. Now the

percent sign will blink on and off, and you may adjust the amount of elevator travel with the

(+) and (–) keys. You may change the initial 50% setting to be anywhere between 0% and

100% (press the plus and minus keys together if you wish to reset to 50%). Remember to be

sure not to have so much travel as to cause binding when both elevator and aileron are

commanded simultaneously.

– 34 –

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6XA Seite 39

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba 6XA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info