Bedienungsanleitung Futaba 6XA (Seite 44 von 64) (Englisch)

28989

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

F/S — Fail Safe Function (PCM mode only)

The Fail Safe function is used to prescribe what the PCM receiver will do in the event radio

interference is received, and doesn’t work with FM receivers. In this menu, you may select from

one of two options of operation for each channel. The “

NORM

” (normal) setting holds the servo

in its last commanded position, while the “

F/S

” (Fail Safe) function moves each servo to a

predetermined position. The default setting is NORM (normal) for all channels.

The use of the fail safe function is recommended from the standpoint of safety. You may

wish to set the throttle channel so that the throttle is moved to idle when there’s interference.

This may give enough warning to allow you to fly towards yourself and recover from the radio

interference. If you choose to specify a failsafe setting, the fail safe data are automatically

transmitted once each minute.

Battery Failsafe

Your system provides a second safety function called Battery Failsafe. When the airborne

battery voltage drops below approximately 3.8V, the battery fail safe function moves the throttle

to a predetermined position or fast idle, if you haven’t set it. If this happens, you should

immediately land! If you need to increase throttle for your landing approach, you may

temporarily reset the failsafe function by moving the throttle stick to idle, after which you’ll have

about 30 seconds of throttle control before the battery function reactivates.

Setting the Failsafe Function

1. Enter the failsafe (F/S) program mode by hitting the two MODE SELECT

keys, then press one

MODE key repeatedly until the F/S menu appears, as

shown.

2. To set the failsafe mode for a channel, move the arrow by pressing the

CURSOR key

repeatedly until the small arrow appears under or over the channel number you want.

3. Now select the type of failsafe you want by pressing one of the

DATA INPUT keys: the (+) key gives you the normal function

(holds the last command), and the (–) key gives you the

F/S or

Failsafe function. Repeat this step for each channel that you are using.

HOLD

FAILSAFE

4. If you have chosen only HOLD settings, you’re done. But if you have chosen FAILSAFE

settings, you will need to tell the transmitter the exact position that you want each servo to

assume when there is interference.

5. Now you’ll input all the control positions. Let’s say that you want the throttle servo to

command idle when interference is received. Use the

CURSOR key to command the set

mode (

SET will begin flashing in the display). Hold the throttle stick in the position you

desire (say a bit above idle), and then press the two

DATA INPUT keys. The servo position is

indicated in the numbers to the lower right, the position is stored in memory, and

simultaneously sent to the receiver. If you have more than one channel you wish to set,

you’ll have to set them all at once by holding all the controls where you want them, and

pressing the two

DATA INPUT keys.

6. Verify that your failsafe programming works by switching off transmitter power and

observing the motion of the servos.

– 39 –

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6XA Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba 6XA

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info