Bedienungsanleitung Futaba 6XH (Seite 21 von 64) (Englisch)

28993

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

AIRCRAFT SETUP INSTRUCTIONS (GENERAL 120 CLASS STUNT PLANE)

The aircraft setup procedure presented

below uses a F3A-class model as an example

and assumes that there are two aileron servos,

one in each wing. You may use a similar

procedure to set up your own model, but your

setting’s numbers and percentages will

probably be different.

1. Be sure that all of your servos are plugged

into the proper receiver channels:

CH1 — Aileron (Right aileron*)

CH2 — Elevator

CH3 — Throttle

CH4 — Rudder

CH5 — Gear

CH6 — Flap (Left aileron*)

* = if FLPR activated

We recommend that you begin your

programming exercise with the servos

installed in the model and connected to the

respective control surfaces. This will enable

you to immediately see the effect of each

programming action we're about to take.

2. Turn on your transmitter and receiver, and

select the desired model memory. To do this,

enter the programming mode by pressing the

two

MODE keys, then press the down MODE

key until “

MODL” appears. Press the CURSOR

key and choose a vacant model memory with

the plus (+) and minus (–)

DATA INPUT keys.

Select it by pressing the

CURSOR key until

“SET” is flashing, then press both the

DATA

INPUT

keys at once. The figure shows

memory #1 being utilized.

There are a number of ways to keep track of

which model is in each memory. You may

attach a small piece of white tape to the

transmitter front and write the model's name

along with the model setup number, or you

may use a notebook, or label the model with

its memory number prominently near its on-

off switch inside the fuselage.

3. Enter the Parameter (

PARA, p. 38) menu by

pressing the down

MODE key three times.

Press the key three times to select the ACRO

model type (four presses gets the HELI

function). Select ACRO by pressing both

DATA INPUT

keys. When the flashing “SET”

appears, again press both

DATA INPUT keys to

lock it in.

flashing

The reason for the separate functions within

the

PARA setup is that these are seldom used,

and the parameter menu provides a convenient

way of bypassing them for most programming

operations.

WARNING: selecting a different model type

will erase the settings in the model memory.

BE SURE you’re in the correct model

memory before selecting a new model type.

4. If your receiver happens to be different

than the transmission mode (as shown it’s

PPM), continue to the modulation (

MOD, p.

40) menu to select the proper mode of

transmission (

F is for FM/PPM transmission,

and

C is for PCM). This should be set to

match your receiver. If you make a change, it

won’t take effect until you cycle the power off

and on again. So if you have changed

modulation, cycle power now.

flashing

5. If your model has flaperons, turn on the

Flaperon function (FLPR, p. 28) in the menu.

To do this, press one of the

MODE buttons

until “

FLPR” appears in the display. Press the

CURSOR key to get the “INH” flashing, then

activate by pressing the plus (+)

DATA INPUT

– 16 –

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6XH Seite 21

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba 6XH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info