Bedienungsanleitung Futaba 6XH (Seite 28 von 64) (Englisch)

28993

Zoom out

Zoom in

Vorherige Seite

1/64

Nächste Seite

(–) keys until they do go the right direction.

Then press the

CURSOR key again, and the

percent indicator will flash. Now you may

input the percentage of mixing. Start out with

10-20% and increase it until the corners in

your loops are square enough.

31. Programmable mixers: now take

advantage of your system’s custom

programming capabilities. You may use

programmable mixers (

PMXI or PMX2, p. 35)

to get rid of unwanted tendencies (for

example, pitching up during knife-edge flight.

For pitching during knife-edge, you want to

apply up or down elevator when you are using

full rudder to sustain knife-edge. Thus, the

master channel is rudder, and the slave is

elevator.

To program this mixing, first get to the

PMXI

window. Press the

CURSOR key once, then

press the (+) to activate it (a flashing

ON or

OFF

will appear, depending on the position of

the Elev D/R switch, which turns mixer #1 on

and off).

Next, press the

CURSOR key once, then press

the

DATA INPUT key until the little arrow is

over the numeral 4, indicating CH4 (rudder) is

the master channel. Press the

CURSOR key

once, then press the

DATA INPUT key until the

little arrow is under the numeral 2, indicating

CH2 (elevator) is the slave channel.

Now, you’ll define the mixing direction. If

your model pitches up with knife edge, you’ll

want to input down elevator for rudder going

both directions. Move the rudder stick to one

side and see which way the elevator moves; if

incorrect, press the

CURSOR key once, then

press the

DATA INPUT keys until it moves

down. Repeat this by moving the rudder stick

to the other side. You’ll end up with a plus

sign for one rudder direction, and minus for

the other direction.

Finally you may input the amount of elevator

mixing on both sides by pressing the

CURSOR key, then the (+) or (–) keys until a

small amount of mixing has been assigned.

Repeat this by moving the rudder stick to the

other side and verifying that the numbers

match for both directions.

Be sure you understand how to use the Elev

D/R to switch to turn the mixer on and off,

since you won’t want this mixing on during

normal flight, only during knife-edge. Later,

after you fly the model you may fine tune the

amount of elevator travel so that the pitching

tendency is eliminated.

The sky’s the limit — you’ll enjoy using your

T6XAs/XHs system!

Pattern Aircraft Flight Trimming Chart

The following chart may be used to systematically set up and trim a model for straight flight and

aerobatic maneuvers. Please note that for best results, trimming should be done in near-calm

conditions. Before you decide to make a change, be sure to try the test several times before

making adjustments. If any changes are made, go back through the previous steps and verify

that they are not also affected. If they are, make further adjustments as necessary.

To test for … Test Procedure Observations Adjustments

1. Control

neutrals

Fly the model straight and

level

Use the transmitter trims for hands-off

straight & level flight.

Change electronic subtrims or

adjust clevises to center

transmitter trims.

– 23 –

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 6XH Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba 6XH

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info