Bedienungsanleitung Futaba 8UAPS (Seite 85 von 105) (Englisch)

29001

Zoom out

Zoom in

Vorherige Seite

1/105

Nächste Seite

Setting Delays

To PMIX-1

function

To OFST-2

function

Delay amount

Range: 0 - 100%

(Initial value: 0%)

Data input keys

These keys are used to move

through the three submenus in

the DELAY function.

1. Aileron delay

Input the desired Aileron delay with

the (+)/(-) keys.

2. Elevator delay

Input the desired Elevator delay

with the (+)/(-) keys.

3. Rudder delay

Input the desired Rudder delay with

the (+)/(-) keys.

• If you're unhappy with what you've

set, you may reset to zero by

pressing the (+) and (-) keys

simultaneously.

The Delay function is automatically activated when either

Offset, Revolution mixing, or Throttle hold are activated.

Channel display

AIL = Aileron

ELE = Elevator

RUD = Rudder

In the helicopter mode, your T8UA system contains two separate programmable mixers

with unique mixing capabilities. You may use mixing to correct any tendencies of the

helicopter during aerobatics that you want to eliminate, making operation more pleasant.

Besides mixing between arbitrary channels, the mixers may be linked with the Advance

menus in the T8UA, or the mixing curve can be offset relative to the master’s neutral. You

may select which switch activates your mixers from the eight switches A-G or throttle, and

you may choose whether the trim from the master also affects the slave channel.. The Link

function is used to ‘link’ programmable mixers with other mixing menus.

The default channels for Mixers 1 & 2 are set to frequently-used mixing combinations as

follows: PMIX-1 = AIL→ELE, PMIX-2 = ELE→THR. The programming method is given

for Mixer #1; the second mixer may be programmed in an identical fashion.

To PMIX-2

function

To DELAY

function

Master channel

(control that

applies mixing)

Data input keys

These keys are used to move

around in the PMIX-1 menu

2. Master channel setting

Select the master channel with the

(+)/(-) keys (the master is the one

that sends the mixing).

If you select "OFS" for the master

channel, the numerical mixing rate

setting affects the slave side only,

providing a fixed offset.

3. Slave channel setting

Select the slave channel (the one

that receives the mixing) with the

(+)/(-) keys.

4. Mixing rate setting

Move the master control in the direction you want to adjust, and

one of the mixing rate displays will flash. Set the mixing amount

with the (+)/(-) keys. Note that you can set the mixing rate

individually for each side of the mix (left/right or up/down).

NOTE: If the amount of mixing is set to 0%, no mixing will occur.

You may reset the rate to zero by pressing the (+)/(-) keys

simultaneously.

Mixing rate

(left or up)

Mixing rate (right

or down)

Slave channel

(channel which

receives mixing)

Range: -100 to +100%

(Initial value: 0%)

1. Activate the Programmable Mixer

Press the (+) key to activate the PMIX-1 function ("ON" or

"OFF" will be displayed, depending on the ON/OFF switch's

position). Use the (-) key to INH

ibit the mixer.)

Default Mixing Setup

When you begin programming a

model, the mixers are set up as

follows (of course, you may change

these default settings):

PMIX-1: AIL>ELE

PMIX-2: ELE>THR

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 8UAPS Seite 85

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info