Bedienungsanleitung Futaba 9CAPsuper (Seite 15 von 109) (Englisch)

29007

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

Stick tip ALocking piece B

Adjusting the length of the non-slip control sticks

You may change the length of the control sticks to make your transmitter more

comfortable to hold and operate. To lengthen or shorten your transmitter’s sticks,

first unlock the stick tip by holding locking piece B and turning stick tip A

counterclockwise. Next, move the locking piece B up or down (to lengthen or

shorten). When the length feels comfortable, lock the position by turning lock-

ing piece B counterclockwise.

Stick lever tension adjustment

You may adjust the tension of your sticks to provide the feel that you prefer for flying. To adjust your springs, you’ll have

to remove the rear case of the transmitter. First, remove the battery cover on the rear of the transmitter. Next, unplug the

battery wire, and remove the battery and RF module from the transmitter. While you are removing the RF module, pay

attention to the location of the pins that plug into the back of the module. Next, using a screwdriver, remove the four screws

that hold the transmitter’s rear cover in position, and put them in a safe place. Gently ease off the transmitter’s rear cover.

Now you’ll see the view shown in the figure above.

Using a small Phillips screwdriver, rotate the adjusting screw for each stick for the desired spring tension. The tension

increases when the adjusting screw is turned clockwise.

When you are satisfied with the spring tensions, reattach the transmitter's rear cover. Check that the upper printed circuit

board is on its locating pins, then very carefully reinstall the rear cover being mindful to guide the RF module connector

pins through the slot in the case. When the cover is properly in place, reinstall and tighten the four screws. Reinstall the

battery, cover and module.

Adjusting Display Contrast:

To adjust the display contrast, from tha home menu press and hold the End button.

Turn the dial while still holding the End button:

clockwise to brighten

counterclockwise to darken the display

Let go off the dial and the button.

Changing Modes:

Hold down the Mode and End buttons while turning on the Transmitter. The screen reads "STK-MODE". Change this to the

correct mode. Note that this will NOT change the throttle and elevator rachets, etc. Those are mechanical changes that

must be done by a service center.

[Note] While changing modes, the transmitter transmits in PPM mode even if the set-up mode is PCM mode.

CAMPac data conversion (9C to 9C super):

Hold down the Mode and End buttons while turning on the Transmitter. Select "T9C-Pac > UPDATE" by Cursol button.

Then press the Dial for 1 second for starting the data conversion. Note that the converted CAMPac cannot be used with a

conventional 9C transmitter.

[Note] While data conversion, the transmitter transmits in PPM mode even if the set-up mode is PCM mode.

Aileron

Elevator

Rudde

Stick Stick

Mode 2 transmitter with rear cover removed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9CAPsuper Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info