Bedienungsanleitung Futaba 9CHFsuper (Seite 45 von 109) (Englisch)

29009

Zoom out

Zoom in

Vorherige Seite

1/109

Nächste Seite

Using FLAPERON (ACRO/GLID ):

The FLAPERON mixing function uses one servo on each of the two ailerons, anduses them

for both aileron and flap function. For flap effect, the ailerons raise/lower simultaneously.

Of course, aileron function (moving in opposite directions) is also performed.

[Note] When changing the polarity of a rate, "change rate dir?" is displayed for a check.

Please set up after pressing DIAL for 1 second and canceling an alarm display. (GLID only)

Once FLAPERON is activated, any time you program CH6 or "flap" (ie. FLAP-ELEVATOR mixing), the radio commands both

servos to operate as flaps. The amount of travel available as flaps is independently adjustable in FLAPERON. A trimming

feature is also available (see FLAP-TRIM) to adjust both neutral positions together for straight-and-level flight or slight

increases/decreases of the flap angle.

Adjustability:

• Each aileron servo's up travel can be set separate from its down travel, creating aileron differential. (See example).

• Each aileron servo's travel when actuated as a flap is separately adjustable.

• AIL-2 can be utilized to use a 5-channel receiver and still have flaperons. NOTE: The AIL-2 function only commands

the channel 5 servo to operate with the aileron servo as ailerons, and to obey the primary flap control (travel adjusted

in FLAP-TRIM.) It does not provide full flap mix capability as when using a 6+ channel receiver and channel 6.

NOTE: Activating flaperons only makes the ailerons work as ailerons and tells the radio how far you want them to move

as flaps IF you then activate other programming that moves them as flaps.

FLAP-TRIM is the flap-trimming feature that allows the flaps to move in reaction to the channel 6 control. It is meant only

for trimming the flaps' center but can also be used as full flap control. (See p. 46).

AIRBRAKE is a feature that drops flaperons as flap, and also compensates with elevator if desired. (See p. 56).

FLAP-ELEVATOR would add elevator mixing into the flap movement from the flap dial after FLAP-TRIM is activated.

END POINT and SUB-TRIM both still adjust each servo individually.

GOAL of EXAMPLE: STEPS: INPUTS:

* If you receive an error message that OTHER WING MIXING IS ON, you must deactivate AIL-DIFF or ELEVON. see p. 44.

Activate twin aileron servos, FLAPERON.

Input 10% less down travel than up

travel (aileron differential) within the

FLAPERON programming. (Decrease right

aileronís down travel to 90%, decrease

left aileron=s down travel to 90%.)

Adjust total flap travel available to

50% of aileron travel available.

Where next?

Open the FLAPERON function.

Activate the function.

Optional: adjust the up/down travel

separately for the 2 servos.(Ex: 90%

down.)

Optional: adjust the aileron's travel

so they move as flaps. (Ex: each servo

flap travel to 50%.)

Close menu.

for 1 second.

(If basic, again.)

to FLAPERON.

AILERON STICK. to 90%.

ILERON STICK. to 90%.

to 50%.

to -50%.

Set FLAP-TRIM: see p. 46.

Set up AIRBRAKE mix: see p. 56.

Mix flaperon's flap motion to another inboard flap (plugged into aux1): see p. 54.

View additional model setups on the internet: www.futaba-rc.com/faq/faq-9c.html

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9CHFsuper Seite 45

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info