Bedienungsanleitung Futaba 9ZAP_part1 (Seite 31 von 78) (Englisch)

29047

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

System Section

TRN—TRAINER SYSTEM

The Trainer function makes it possible for the

instructor pilot to choose which functions and

channels are to be used for instruction, making it

possible to match the training difficulty to the

student's skill level. A special function called Cor-

rection Control makes it possible for the instructor

to make corrections without overriding the stu-

dent's inputs. Two transmitters must be connected

by an optional Trainer/Data Transfer cord, and the

Instructor transmitter should be programmed for

trainer operation, as described below.

Operation is simple: when the Instructor acti-

vates the trainer switch, the Student has control of

the aircraft (if the mixing mode is turned on, the

Instructor can make corrections while the student

has control). When the Instructor releases the

switch, control is regained. This is very useful

when the Student gets the aircraft into an undesir-

able situation.

The training system will work with any PCM

1024Z series transmitter. Futaba's 5U and 7U

series of transmitters may also be connected for a

student's usage. Note that in some cases a low

battery warning may appear on the 7U series, but

operation is unaffected by this warning.

- ACT/ INH Selection

Return to System

Channel Selection Keys

ON/OFF Toggle

Switch Setting

Instructor-Controlled

Channel Selection

Correction Mixing

Channel Selection

TRAINER MODE SETUP

To place the PCM 1024Z into the Trainer mode, press

the

TRN

key

from the System Menu. The

Rkey

succes-

sively toggles between ACTIVATE and INHIBIT, with the

current mode displayed just to the left of the key. Once

activated, the operation mode for each channel is selected.

PLACE THE STUDENT TRANSMITTER IN PPM PULSE

MODE. The instructor's transmitter may be in any trans-

mission mode.

Controls and functions in both transmitters should be

matched. With two PCM 1024Z transmitters, matching

may be done easily using the Data Transfer

DTN

key

described on page 30. When using 5U and 7U transmitters,

be sure that EACH transmitter command works properly

before flying. All channel assignments and throw direc-

tions must be identical.

The Instructor's power switch should be turned on,

with its antenna fully extended. The student's transmitter

switch must always be turned off. In addition, the student

must not operate his trainer switch, or problems may

occur.

CHANNEL SELECTION

Select the desired channel using the E to L up-arrow

keys. At this point, one can choose from student-only

control and correction control. For Student-only control,

press the

P (TRN)

key. This will cause the lower

square in the chosen channel to become filled. For Cor-

rection

control,

press

the

(

MIX

)

key. This action

fills in the upper square in the active channel. If neither

square is filled, only the instructor can control this partic-

ular function.

SETTING UP THE ON/OFF SWITCH

The default switch for the trainer ON/OFF function is

the spring-loaded switch SW(H), with forward in the ON

position. This switch must be held ON continuously for

the student to have control. For convenience, the alter-

nate switch function (ALT) may be used to set this switch

so that it is alternately turned on and off successively

each time the switch is operated.

The location of the activation switch, as well as its

direction and operation, may changed using the switch

setting screen available by pressing the

(SWT) key.

For more details on the switch setting menu, see page 37.

System Section, Page 29

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZAP_part1 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info