Bedienungsanleitung Futaba 9ZAP_part1 (Seite 44 von 78) (Englisch)

29047

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Model Setting Section

F/S—FAILSAFE/HOLD SETTING

The Failsafe function may be used to set up

positions

that

the

servos

move

the

case

radio interference. This function only works with

PCM receivers (FM receivers do not have the fail-

safe capability).

You may set either of two positions for each

channel: normal, where the servo maintains its last

commanded position, or Failsafe, where each servo

moves to a predetermined position. You may

choose either mode for each channel.

The

PCM

1024Z

system

also

provides

you

with

an advanced battery monitoring function that

warns you when the receiver battery has only a

little power remaining. In this case, the throttle is

moved to the defined failsafe position, or if one

was not defined, to a medium speed position. The

throttle may be released by operating a predefined

control on the transmitter (the default is throttle),

do not continue to fly — land as soon as possible.

Remember, if your throttle suddenly moves to a

position you did not command, land at once and

use the voltmeter function, with a 250 or 500 mA

load, to check your receiver battery. Quite a few

models have been saved from unnecessary crashes,

thanks to the battery failsafe function.

Failsafe Setting Procedure

In the Model Menu, press the Failsafe key (F/S) to

get the Failsafe menu shown below.

Servo Failsafe

Position

Battery Failsafe

Release

Normal/Failsafe

Selection Keys

Position Setting Key

Return to Model

Channel Selection Keys

Now you must decide which channels you want to go

to preset positions, and which you want to maintain their

last commanded position.

Use the Up-Arrow keys (F to M) to select the

desired channel. Now, press the

F/S

key to switch that

channel to the failsafe mode. Hold the stick, knob, or

slider at the desired position and press the

SET (O)

key. The chosen servo command is now displayed in

percent underneath the selected channel buttons.

If you wish to reset the channel to the normal (hold)

function, press the

NOR (Q)

key. If you desire the

failsafe function later, the last setting is remembered and

displayed when the

F/S

key is again activated.

If you want the Battery Failsafe function to move the

throttle to a defined position, be sure to set it before you

leave this menu.

Battery

Failsafe

Release

Function

This function releases the throttle from is held posi-

tion after indicating that your receiver battery is low. You

did

remember

set

throttle

failsafe

position,

didn't

you? REMEMBER TO LAND AS SOON AS POSSIBLE.

Call the Battery Failsafe setting screen by pressing the

BFS

(

) key while in the Failsafe menu. Now, you

may choose that moving the throttle resets the condition,

or select another stick or switch deactivates it.

To set a desired throttle release position, move the

throttle stick to the point at which you wish the failsafe

to be released (perhaps low throttle but a bit above idle).

Now press the SET (Q) button to set this position

(the position is displayed in percent).

If you want to use another function to switch off the

battery failsafe, either choose the desired stick motion, or

move to the switch setting menu by pressing SWT (

For more information on the switch setting menu, refer

to page 37.

When you are through setting all the desired channels,

press the END key (N ) to return to the Model Menu.

Model Setting Section, Page 42

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZAP_part1 Seite 44

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info