Bedienungsanleitung Futaba 9ZAP_part1 (Seite 68 von 78) (Englisch)

29047

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Common Condition Section

Programming the Mixers

Activation of command

In the Condition Menu, press the PMX key to get the

PROG MIX menu shown as Screen 1 in the top of the

illustration below.

Selection and Activation of Mixing Menu (Nos. 1 to 5)

Press the number key associated with the mixing menu

that you wish to program with the 1 to 5 ( F to H )

keys. Press the

key (moves to Screen 2 display shown

below), then activate the mixer by pressing the ACT—

Fkey.

You may

inhibit

the

mixer

by pressing the INH

Gkey.

Choosing the Mixing Type

Press the D key to get to the mix type selection

menus. Now, you may select the Linear type by pressing

the LIN E key, select the hovering type by pressing

the

HOV G

key, select the 7-point curve type by

pressing the

CRV H

key, or select the Rate Control

type by pressing the

CTL

I key.

Master channel setting (not for offset and hovering type

mixing)

To select the control to be used as the Master channel,

press the B key. then press the key of the channel to be

set with the E to L keys. Depending on the Model

setup, the following keys will appear on the bottom of

the screen:

Airplane:

Helicopter:

Sailplane:

Mixing ON/OFF switch selection and ON/OFF direction

setting

When a mixer is first activated, an ON/OFF switch is

not defined. If you wish to define an on/off switch to

control the mixing, call the switch setting screen by

pressing the

SWT P

key. For a description of the

switch setting method, see page 37.

Mixing Rate Inputting

To input the mixing rate, call the rate setting screen

by pressing the

NXT O

key. This action calls up the

menus shown in the figure as Screen 3.

If the linear type of mixing is selected, you may offset

the

Mixing switching point setting by

pressing

the B key.

then setting the master control to the desired switching

point, and pressing the

SET F key.

Mixing Rate Setting, Sides A and F

To input the numerical mixing values for the A side of

Linear

mixing, press the C key. You may then set the

rate with the numeric setting keys E to M. The mixing

rate is initially set to a value of +50%, but may be set

anywhere in the range between —100 to +100%. Note

that on the setting screen graph, the top is — and the

bottom is+.

You may now set the values for Side B mixing as side

A was done above.

If Offset mixing is selected, you may set the offset

with the rate setting keys

E to

M The initial offset

value is 0%, but you may set this anywhere between —100

and +100% with the numeric keys.

If you will be linking this mixer with other mixers,

press the

LNK M

key. Linking is turned on and off

alternately each time the key is pressed. When linking is

ON, a "-»" is displayed in front of the Master channel

name.

Slave channel setting

To select the Slave channel, press the C key and

select the desired channel with the

E to M

keys. To link

the Slave channel with other mixing, press the LNK M

key. A "-»" is displayed after the channel name.

Trim ON/OFF Setting

Trim ON/OFF only applies to Linear type mixing. To

select Trim ON/OFF, press the R key. To add the master

trim

operating

rate

mixing,

press

the

ACT F

key. If

you do not wish to add trim operating rate to mixing, use

the INH G

key.

Master Channel MIX Mode Definition

This definition does not apply to offset-type and

hovering-type mixing. To define the Master channel mix

mode, press the

key. If you wish to add AFR, D/R,

and curve set rate to mixing, press the

MIX F

key, if

you do not wish to add AFR, D/R, and curve set rate to

mixing, press the

(UN) key.

SERVO

RESPONSE

OFFSET RANGE

OFFSET RATE

STICK MOTION

If Hovering mixing is selected, you input the Slave

channel

neutral

position

offset range

setting

using the C

key, and set the offset range with the rate setting keys F

to M . This value is initially set 5to 100%, but can vary

anywhere between 0 and 100%.

Now

you

will

set

Slave

channel

neutral

width

setting.

To do this, press the D key and set the offset with the

rate setting keys E to M. This value is initially set to

0%, but can vary anywhere between 0 and 100%.

Common Conditions Section, Page 66

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZAP_part1 Seite 68

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info