Bedienungsanleitung Futaba 9ZAP_part2 (Seite 8 von 78) (Englisch)

29045

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Airplane Section

ELEVONS

(EVN)

This function may be used to set up the con-

trols for delta wings, flying wings, and other tail-

less

aircraft

which

need

combined

aileron

and

elevator functions. Receiver CH1 and CH2 are

made the operating channels for the two elevons,

and differential operation is possible.

The elevator deflection angle and operating

direction can be set for each servo. For conve-

nience, the elevon deflection angles can be trim-

med in flight when a volume-setting lever is acti-

vated (this setting is performed by the aileron

differential

ADF

function

page

125).

Setting Up Elevon Mixing

Activation of command

In the Condition Menu. press the

EVN

key to get

the ELEVON Mixing menu as shown below. Use the

key to activate mode setting, then press the

ACT

or INH keys ( F and G ) to activate or inhibit Elevon

Mixing.

Delta-Wing Aircraft

Elevons

Mode setting

Aileron 1 left

side rate

Aileron 2 left

side rate

Elevator 2 rate

Aileron 1 right

side rate

Aileron 2 right

side rate

Elevator 1

rate

Return to

condition menu

Mode Activation

Setting the Aileron 1 Rates

You now

set

the

left-side

rate

for

Aileron

Press

the

key to activate left rate setting for Aileron 1 and set

the rate with the numeric keys E to M . The number

keys 0 through

100

input the value directly. The +

and - keys increase or decrease the value by 1. The

+/-

key may be used to reverse the throw direction.

If you are not sure what you are changing, hold the

stick to one side and press different keys — if there is no

effect, move the aileron stick to the other side and con-

tinue. Your setting may vary from —120 to +120%, the

initial value is +100%.

Now

set

the

right-side

rate

for

Aileron

Press

theQ

key to activate Aileron 1 right rate setting and set the rate

with the numeric keys as before.

Setting the Aileron 2 Rates

This

procedure

repeated for Aileron 2.

Press

theC

key to activate left rate setting for Aileron 2 and set the

rate with the numeric keys E to

as before.

Now set the right-side rate for Aileron 2. Press the

P key to activate Aileron 2 right rate setting and set the

rate as before.

Setting the Elevator Rates — 1 and 2

You now set the rate for Elevator 2. Press the D key

to activate rate setting for Elevator 2 and set the rate with

the numeric keys

E toM

Now set the rate for Elevator 1. Press the O key to

activate Elevator 1 rate setting and set its rate with the

numeric keys.

Checking Your Work

After you have set up the Elevon rates, be sure that

they move the correct directions. For up elevator com-

mand, both elevons should move upward. For right

aileron command, the trailing edge of the right-hand

surface should move up, and the trailing edge of the left-

hand surface should move down. If they do not, use the

+/- to reverse the direction as needed.

Use the END ( N ) key to leave this menu.

Airplane Section, Page 84

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZAP_part2 Seite 8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info