Bedienungsanleitung Futaba 9ZAP_part2 (Seite 71 von 78) (Englisch)

29045

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Sailplane Section

FLAP-ELEVATOR Mix

(F-E)—2-S

This function is used to compensate for trim

changes when flaps are deployed for slow flight or

landing by mixing in a small movement of elevator.

The elevator should be adjusted to move only a

small deflection amount: too much elevator can

make the model difficult to control.

The amount of correction can be adjusted

separately for both positive and negative flap in-

puts, and the neutral mixing position can be offset

from the flap neutral position. Flap-to-elevator

mixing can be turned on and off during flight by

setting a switch, but if an ON/OFF switch is not

set, it remains on all the time. The amount of mix-

ing can be changed by setting a volume control.

Setting Up Flap-to-Elevator Mixing

Activation of command

In the Condition Menu. press the F->E key to get the

FLP

TO ELE menu shown below.

Use the A key to activate mode setting, then press.

the ACT or

INH

keys ( F and G ) to activate or

inhibit flap-to-elevator coupling.

Offset Position Setting

Use the

key to activate offset setting mode.

Then set the flap control to the offset position, and press

the SET key F to store the desired position in mem-

ory.

Setting the Mixing Ratio — Down and Up Side

You now set the amount of mixing for down flap

command. Press the C key to activate mixing ratio for

the down direction and set the value with the numeric

keys E to M The number keys 0 through

100

input

the value directly. The + and - keys increase or de-

crease the value by 1. The +/- key may be used to

reverse the throw direction. Your setting may vary from

-100 to +100%, the initial value is set to +50%.

Now set the amount of mixing for the up flap com-

mand. Press the D key to activate mixing ratio for the

Up direction and set the throw with the numeric keys as

before.

On/Off Switch Setting

Initially an activation switch for is not set, meaning

that once activated, this function is on all the time. If you

would like to set a switch to turn it on and off, call the

Switch Setting screen by pressing the

VOL O

key.

Then use the keys to choose the desired switch location

and on direction. For more information on the switch

setting method, see page 37.

Trim volume setting

You may set up the Flap-to-Elevator mixing so that its

effect may be changed in flight by moving a trim control.

The trim control allows you to adjust the volume within

± 25% of the set mixing rate, which can be handy for

getting the best value while flying the model. This option

is not activated at initial setup.

Call the volume setting screen by pressing the

key, and select the desired control using the screen

menus (for a description of the volume setting method,

see page 37).

Use the

END ( N

) key to leave this menu.

Sailplane Section, Page 147

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZAP_part2 Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info