Bedienungsanleitung Futaba 9ZHP_part1 (Seite 17 von 78) (Englisch)

29011

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Manual Introductory Section

SYSTEM STATUS AND ALARM DISPLAYS

The PCM 1024Z System provides you with a

number of indicators and displays to show you

that your system is operating correctly. This sec-

tion will explain each display's function

EXT MEM ERR display

This display blinks when a data error occurred

during transmission of data between the trans-

mitter memory and the memory module. Turn

off the power. DO NOT REMOVE OR INSERT

THE MEMORY MODULE WITH THE POWER

TURNED ON. THIS ACTION COULD DE-

STROY THE MODULE.

ON AIR display and beep

This display is turned on when radio waves are

being transmitted.

Enter ID No. display

This display indicates when the security mode

is set. In this case, model data cannot be

changed. See the section on data protection to

reset this display.

LOW BATTERY display and beep

This display and warning beep are to notify the operator

that the transmitter battery is low.

TO PREVENT PROBLEMS, LAND THE MODEL

AS SOON AS POSSIBLE.

PLL ERROR and beep

This display blinks and sounds when the synthesized

frequency module is removed during operation.

Be sure to turn off power before installing the module.

Do not remove or insert the module with power on.

(D BACK-UP BATTERY FAILURE - DO NOT FLY

This warning is displayed when the data stored has been

lost for some reason. A beep will sound simultaneously.

When the power switch is turned on again, the error dis-

play goes off and the data returns to the factory default

state. The lithium data backup battery needs to be re-

placed, or there is a fault in the system. Return the

system to the Futaba service center for assistance. The

life of the lithium battery varies, but is usually at least

five years.

2 CURRENT MODEL IS*** ##.NAME ***

This display shows the model number and model name

currently stored in the active area of the transmitter. It

will disappear a few seconds after the system is turned on.

DATA PAC IS MISSING - LOADED MODEL1

This message is displayed whenever the transmitter is

turned on with the memory module removed and the

active model data was stored on the module. Without the

desired model data, the system loads the Model 1 data

instead.

3 CAUTION: NON-DEFAULT COND IS ACTIVE

This warning message is displayed, and a beep sounds,

whenever the transmitter is turned on with a flight con-

dition switch activated. This display and alarm will turn

off as soon as the flight condition switch is turned off.

4 CAUTION: SPECIAL MIX FNCT IS ACTIVE

This message and alarm are activated when the transmitter

is turned on with a mixing switch activated. The alarm

monitor above the power switch also blinks. All of these

will stop as soon as the mix switch is changed to its OFF

position.

CAUTION: ENGINE CUT FNCT IS ACTIVE

If the power is turned on with the engine cut switch on,

this message is displayed and a beep sounds. When the

engine cut switch is turned off, the display and alarm

stop.

Manual Introductory Section, Page 15

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZHP_part1 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info