Bedienungsanleitung Futaba 9ZHP_part1 (Seite 34 von 78) (Englisch)

29011

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

System Section

PC—COPY Condition Function

This function may be used to copy individual

flight conditions. One use would be to copy the

default flight condition, with all its subtrims,

mixing, etc. to another flight condition, and chang-

ing only the necessary parts. This procedure can

save a lot of time and unnecessary effort.

This

function

may

also be

used

delete

flight

conditions (other than default) from the CAMPac

memory module. The MSL (Model Select) func-

tion

may

used

delete

the

model

data.

The entire model data may be copied under the

following conditions:

1. If the destination type is different from the

source, the set data are copied.

2. If the destination type is the same as the source,

all the set data are copied except for the condi-

tion name.

3. If the source is not allocated to a model mem-

ory ("00"), all the set data, including the model

name, is copied.

Destination Condition Number -

Source Condition Number

-Show Condition List

-Confirm Condition

Number

Return to System

Numeric Keys Used to Choose Condition Numbers

Reading the Condition List

To display the condition list, press the

LST (R)

key. This displays conditions 1—10. To view the next ten

conditions, press the

NXT

(P) key. To view the

preceding ten conditions, press the

PRE

(O) key.

Conditions nos. 01-50 are stored in the transmitter, and

nos. 51-70 are stored in the optional CAMPac memory

module.

Flight Condition Copying

Follow the following instructions to copy one flight con-

dition to another:

1. Use the numeric keys on the display bottom to input

the Source condition number. The 1,15,30,45,60,

and 72 keys input the key's value directly. The ( + )

and ( - ) keys may be used to increase or decrease

the displayed value by one for each key press. When

you are satisfied with the source number, press the

SET (O)

key.

2. Now use the numeric keys to enter the Destination

condition number. Once again, enter the condition

number with the numeric keys at the display bottom,

and press the

SET

(

) key.

3. If you are happy with both condition numbers, press

the

YES (L)

key to execute the copy. If not, press

the NO (M) key to stop copying.

4. To continue copying further sets of conditions, press

the CNT (L) key and repeat the instructions

beginning from step 1.

To end copying, press the

END (N)

key.

Flight Condition Deletion

To delete conditions from the CAMPac memory module,

follow the following instructions:

1. Press the

DEL (A

) key to enter the deletion mode.

2. Press the + or - (F or G) keys to select the con-

dition to be deleted.

3. If the condition is correct, press the DEL (Q) key,

then confirm using the

YES

(L) key.

4. To continue deleting, press the CNT (L) key and

repeat the instructions beginning from step 1.

To end copying, press the END (N) key.

Condition No. (

01~50: Transmitter

51~72: Memory Module

System Section, Page 32

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZHP_part1 Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info