Bedienungsanleitung Futaba 9ZHP_part2 (Seite 17 von 78) (Englisch)

29053

Zoom out

Zoom in

Vorherige Seite

1/78

Nächste Seite

Airplane Section

SNAP ROLL

(SIMP)

Your PCM 1024Z system may be programmed

to perform snap rolls by flipping a switch. Four

snap roll directions can be defined, and the preset

positions of the aileron, elevator, and rudder

servos can be set for each one.

You may activate a safety switch to ensure that

snap rolls are not accidentally commanded while

the

landing

gear

down,

even

the

snap

roll

switch is turned on accidentally.

Setting Up The Snap Roll Presets

Activation of command

In the Condition Menu, press the

SNP

key to get the

SNAP ROLL menu as shown below.

Snap Roll Directions

Direction Switches

(Note: These snap roll direction setting switches are only present on the T9ZAP systems, not on the T9ZHP)

Mode setting

Rate

setting

-Throw setting

ON/OFF switch

setting

Safety switch setting

Return to condition

Mode selection

Use the

key to activate mode setting, then

press the

ACT

INH

keys ( F and G ) to activate

or inhibit the function.

Inputting the Snap Roll Preset Control Positions

We'll start with the 1-2 direction (Right/Up) snap

roll setting. Press the R key to get to the setting menu,

then press the

1-2

F key.

set

the Aileron

servo

throw setting,

press

theB

key. Use the numeric keys

E to M

to input the desired

preset condition. The default is +100%, but you may use

anything between -110 and +110%.

Now we'll set the Elevator servo preset. Press the C

key. and set the preset with the numeric keys

This also has a default of +100%, but you may use any-

thing between -110 and +110%.

The last part of the setting is for the rudder position.

Press the D key, and enter the rate that you want the

rudder to move with the numeric keys E to M. This

setting also has a default of +100%, and may be set any-

where between -110 and +110%.

This procedure should be repeated for the

1-1

direction (Rright/Down) snap roll setting,

2-2

direction

(Left/Up) snap roll setting, and 2-1 direction (Left/

Down) snap roll setting.

Snap Roll Switch ON/OFF Definition

SW (H) is defined to be the Snap Roll switch, and is

turned ON at the forward position at initial setting. If

you'd like another switch, call the switch setting menu by

pressing the

SWT

P key. For a description of the

switch setting method, see page 37. Caution: if you define

a switch that doesn't have a spring return, the Snap Roll

function will remain on all the time!

Snap Roll Safety switch setting

A safety switch should be used to prevent accidental

operation of the snap roll function. To examine the snap

roll safety switch settings, call up the switch setting screen

by pressing the SWT

key. The function initially

defines SW (F) for Mode I, (G) for Mode II to be the

safety switch. You should set the ON direction of the

safety switch to match the landing gear switch position

when the landing gear is down. When this switch is ON,

the snap roll function is inhibited.

Use the

END N

key to exit this menu.

Airplane Section, Page 93

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba 9ZHP_part2 Seite 17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info