Bedienungsanleitung Futaba FP2GS (Seite 3 von 4) (Englisch)

30066

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

•A common power supply regulator and diode may also be supplied with the speed controller, depending on the vehicle

kit. Since they cause a voltage drop, always remove them.

TO BUYERS OF THE FP-2GS (FP-R102GF)

When using a Futaba motor control amp instead of

the speed controller supplied with the vehicle, turn

off the ASP (Adjustable Safety Position) system as

shown in the figure.

R102GF ASP

release

connector

Insert the ASP release co-

nnector packed "with

the

set at this 2P connector

(male pins) on the

printed

wiring board.

Fig. 5

•Set the transmitter power switch to ON, then set the receiver

power switch to ON. The servos stop near the neutral position.

Operate the transmitter sticks and check if each servo faithfully

follows operation of the sticks.

•Connect the pushrod to each servo horn, then check if the direc-

tion of travel of each servo matches the transmitter operation.

•Operate each servo over its full travel and check if the pushrod

binds or is too loose. Applying unreasonable force to the servo

horn will adversely affect the servo and quickly drain the battery.

Be especially careful when using 8.4V.

•Always make the full stroke (including trim) of the servo horns

somewhat larger than the full travel. Adjust the servo horns so

that they move smoothly even when the trim lever and stick are

operated simultaneously in the same direction.

• Be alert for noise.

Always solder a noise killing capacitor to the running motor. If

metal parts touch each other due to vibration, noise will be gener-

ated and cause the receiver servos to operate erroneously. We re-

commend the use of noiseless parts.

• Even though the receiver antenna wire is long, do not cut

bundle it. The range of the radiowaves will be shortened.

• A spare horn is provided. Use it as required.

•Wrap the receiver in sponge rubber and wrap rubber bands around

the sponge rubber. Mount the receiver so it is not exposed to vi-

bration, does not touch the frame, and does not move.

•When the receiver is installed on a board or used where it may be

splashed with mud and water, place it in a plastic bag, etc. and

wrap a rubber band around the open end of the bag to waterproof

and dustproof the receiver. After use, remove the receiver from

the bag to prevent condensation.

• Use the rubber bands wrapped around the receiver to hold the

servo and switch leads.

•After mounting is complete, recheck each part, then check the

transmitting range by making the transmitter antenna as short as

possible and extending the receiver antenna fully and operating

the set from a distance of 20m to 30m. The movement of each

servo should follow the movement of the transmitter sticks.

•The crystal can be changed from the outside of the receiver case.

Always use a Futaba transmitter and receiver crystal pair as the

replacement crystals.

Fig.

• Install the servos firmly. Install the servo to the servo tray

as shown in the figure. In other cases, install the servo as

described in the model manufacturer's manual.

REPAIR SERVICE

• When requesting repair of trouble that has occurred suddenly

of from long use, describe the trouble symptoms in as much

detail as possible.

This will facilitate detection of the trouble point and shorten

the repair period greatly.

•

Defects caused

faulty

materials

workmanship

will

corrected free of charge.

• This limited warranty is null and void if the set has been tam-

pered with or disassembled.

Refer to warranty statement for details.

WORLD SALES & SERVICE FACILITIES

Australia: FUTABA SALES AUSTRALIA PTY. LTD., Lebanon:

MELBOURNE TEL: 211-4788

Argentine: MODELISMO AE RONAUTICO DEGA SRL. New Zealand:

BUENOS AIRES TEL: 393-2299

Canada: UDISCO LTD., MONTREAL

TEL: 481-8109 Norway:

Chile: HOBBY LANDIA, SANTIAGO

TEL: 743957 Singapore:

Denmark: FUTABA IMPORT DENMARK,

COPENHAGEN TEL: 02-91-0101 South Africa:

England: RIPMAX LIMITED, LONDON

TEL: 01-8048272 Spain:

Finland: NORETRON KY. HELSINKI

TEL: 90-488880 Sweden:

Greece: C. & G. MACR1YIANNIS CO., PIRAEUS

TEL: 021-3604391 • or 021-41 76191 U.S.A.:

Hong Kong: RADAR CO. LTD. TEL: 3-680507

Italy: RADIOSISTEMI SRL, Carrara W.Germany:

TLX: 500494 FORTIMI

FAX: 0039-585-52247

KHAIRALLAH MODELCRAFT, BEIRUT

TEL: 326-681

AMALGAMATED WIRELESS

(AUSTRALIA) N.Z. LTD. WELLINGTON

TEL: 58-979

HARALD LYCHE CO. A/S, Drammen

TEL: (03) 8339 70

SINGAPORE HOBBY SUPPLIES

TEL: 533-0337

REDIPAK (PTY.) LTD.,

JOHANNESBURG TEL: 21-1511

HOBBY & TOY INTERNATIONAL,

VALENCIA TEL: (96) 357 23 93

RADIO CONTROL CENTER,

JONKOPING TEL: 036-145360

FUTABA CORPORATION OF AMERICA,

CALIFORNIA TEL: 213-537-9610

ROBBE MODELLSPORT GMBH,

GREBENHAIIM TEL; 06644-870

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP2GS Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info