Bedienungsanleitung Futaba FP7FGH (Seite 13 von 16) (Englisch)

30030

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Rate gyro FP-G152

Fig.

Connected servo (rud-

der servo for helicopter)

neutral position trim-

mer (This trimmer is

operative even when

the control box power

switch is set to OFF.)

Gyro output polarity switch

Remove

these

screws.

and

remove

the

case.

Gyro body

Connect to receiver

retract or

auxiliary

channel

(for gyro

sensitivity switching)

for Receiver

Control amp

Control box

Gyro output

trimmer

Jumper

connector

for Rudder Servo

Five battery pack 6V connector Motor regulated

power supply. (Insert the jumper connectors when

the power supply is shared with the receiver.)

•Connect the servos and switches firmly as

shown in Fig. 20. Then extend the transmitter

and receiver antennas fully.

•Set the transmitter power switch to ON. then

set the receiver power switch to ON. The servos

stop near the neutral position. Operate the

transmitter sticks and check if the correspond-

ing servos faithfully follow operation of the

sticks.

•After setting the pushrods at the servo horns,

check that the direction of operation of the

transmitter sticks and the direction of opera-

tion of the rudders are the same.

•Operate each servo horn over its entire operat-

ing range and check if the pushrod binds, or is

too loose. Applying unreasonable force to the

servo

horn

will

adversely

affect the

servo

and

quickly drain the batteries. Always make the

operating width of each rudder somewhat larger

than the full stroke (including trim) of the

servo horn. Adjust the servo horns so that

operate

smoothly

even

when the

trim

lever

and

stick lever are operated simultaneouly in the

same direction.

•Be alert for noise.

If engine vibration causes metal parts to touch,

noise will be produced and the receiver and

servos may operate incorrectly. We recommend

the use of noiseless parts.

•When installing the switch, cut a rectangular

hole somewhat larger than the full stroke of the

switch and install the switch so it moves smo-

othly from ON to OFF. When the switch is

mounted inside the fuselage and is turned ON-

OFF with wire, install the switch mount as

described above. Install the switch where it will

not come into direct contact with engine oil,

dust, etc.

•Even though the receiver antenna is long.

not cut or bundle it.

•The

servos,

Ni-Cad

battery,switches,extension

cords, and crystals of FP-7FGH are the same

as those of the high-quality J Series. The crystals

are extremely precise and are identified by

color (red and green). Use Tx and Rx crystals

of the same color.

•A spare horn is supplied. Use it as needed.

•Wrap the receiver in sponge rubber. Place the

receiver in a plastic bag and wrap a rubber band

around the open end of the bag to waterproof

and dustproof the

receiver.

the

same

with

the receiver/servo battery.

•Use the rubber bands wrapped

around the

receiver to hold the servo and switch leads.

•After mounting is complete, recheck each

part, then make the transmitter antenna as

short as possible, extend the receiver antenna

fully,

and

operate

the

set

from

distance

20m to 30m. The movement of each rudder

(servo) should faithfully follow the operation

of each stick of the transmitter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP7FGH Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info