Bedienungsanleitung Futaba FP8SSAP (Seite 19 von 44) (Englisch)

30094

Zoom out

Zoom in

Vorherige Seite

1/44

Nächste Seite

ADJUSTMENTS AND FLIGHT TECHNIQUES

•USING

ATV

(ADJUSTABLE

TRAVEL

VOLUME)

GENERAL - ATV (Adjustable Travel Volume)

allows independent adjustment of servo maximum

throw in each direction (without affecting the

neutral position). This is also sometimes referred

to as "separate endpoint adjustment". ATV is very

convenient when for example: a model requires

more DOWN elevator deflection than UP for equal

inside and outside loops (with equal control stick

deflection). Other aircraft may require slightly

different RIGHT or LEFT aileron or rudder

deflection to give equal response in each direction

(due to engine torque, precision of the model,

etc.). Two different ATV functions are possible

with this system. Memory (Pushbutton) ATV and

2ND

ATV.

MEMORY (PUSHBUTTON) ATV

This type of ATV is available on all eight channels.

Servo travel is adjusted as outlined in the example

below.

NOTE: Memory ATV settings are retained in the

transmitter memory circuit even when the power

switch is turned OFF. They are lost however, if

the transmitter

Nicd

battery

nears

full

discharge

is removed for servicing.

ATV SETTING

Switch switches S [

49] and R [48]

Press button [46] or [47] while holding the aileron

stick in the full position.

Fig.

MEMORY (PUSHBUTTON) ATV - (Aileron CH1

used as example)

1. First, set Function Select Switch [49]

ATV

position.

2. Set Channel Select Switch [48]

to 1 (Ail.).

3.Set

the transmitter and

receiver

power switches

ON and check for proper servo operation.

4.Move the Aileron stick to full RIGHT aileron,

hold it in that position, and set servo movement

to the desired Right aileron deflection angle by

pressing Button 46 or 47].

5.Repeat Step 4 for LEFT aileron.

6. For other

channels,

select

the channel

with

switch 48 and adjust ATV as desired.

7. When all adjustments are completed, set the

Function Select and Channel Select switches

([48]

and

[49)

OFF.

8. To clear the ATV settings on all channels, set

the Function Select switch [49] to RESET and

Channel Select switch [48] to POSITION 2 (Pos.

2 = ATV when [49] is on RESET) and press

Buttons 46 and [47] simultaneously. ATV is

cleared

ALL

CHANNELS and

servos

will

move to 100% of their maximum throw.

9. If only one channel is to be cleared or changed,

simply repeat Steps I through 5 with Chan-

nel Select Switch [48] set to the appropriate

channel.

ATV/FS BUTTON

•These two pushbutton switches are used for servo deflection angle setting of ATV. FS or HOLD func-

tion, servo test start & stop; reset; battery FS memory set, etc.

——————————————————————[46]

This

pushbutton

switch

used

when:

1 Making the ATV servo deflection angle larger.

2 Turning the FS function on.

3 Starting

the

servo

test.

[47] This pushbutton switch is used when:

1 Making the ATV servo deflection angle smaller.

2 Turning the HOLD function on.

3 Stopping the servo test.

When button [46] and [47] are pressed at the same

time, reset or battery FS memory setting is pos-

sible. At this time, lamp A of memory lamps 22

goes out momentarily so that setting can be moni-

tored.

Fig.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP8SSAP Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info