Bedienungsanleitung Futaba FP8SSHP (Seite 14 von 36) (Englisch)

30098

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

30 Power switch

Transmitter lock-type power switch. To turn the switch

on and off, pull the knob forward and set it to the de-

sired position.

31 Antenna

Strong 1m 10cm telescoping antenna. Extend the an-

tenna to its full height when using the transmitter. The

antenna will lock in place with a click when pulled up

its full height.

32 Level meter

•This meter indicates the transmitter battery voltage

and output power (power meter).

•When the antenna [31] is fully extended and the power

switch [30] is set to ON, the pointer should deflect

the white zone.

•If the transmitter RF module [35] is removed, the

level meter

pointer

will

not

deflect

even

the

power

switch [30] is set to ON.

• If the meter pointer deflects to the red zone, indicat-

ing that the Nicd battery voltage is low. the range of

the radiowaves will become shorter and the tacho-

meter/timer

[27]

battery alarm [5] will operate. If the

meter pointer deflects to the boundary between the

white and red zones, recharge the battery.

33 Rudder button

•While this button is being pressed, the rudder moves

to the deflection angle preset at trimmer [17] on the

trimmer panel at the back of the transmitter. After

the time set at trimmer [18] elapses, the rudder servo

returns to the neutral position. This is convenient

when making 540" turns.

•The

rudder

servo

left and

right

throw

can

set

with

trimmer [17] . When fail safe switch [19] is set to the INH

position, the rudder button [33] becomes inoperative.

When the fail safe switch is set to the RUD.REV

position, the rudder button becomes operative.

34 Hovering memory switch

•This switch turns the memory function which memo-

rizes the rudder mixing hovering point on and off.

When it is set to OFF, the revolution mixing knobs

[17] and [18] become inoperative.

•When this switch is set to ON when hovering,

the

position of the throttle lever [3] is memorized.

•The revolution mixing up knob

[17]

and revolution

mixing down knob [18] can be independently adjusted

and set from the throttle lever 3 .

•Mixing can be adjusted with-

in this range with the High

revolution mixing up knob

[

Mixing can be adjusted with-

in this range with the revolu-

tion mixing down knob 18

Throttle lever hovering posi

tion (Position at which the

hovering memory switch 36

was

set

ON.)

Fig.

35 Transmitter RF module

Change this module to switch frequency among

different bands.

Transmitter

crystal

Fig.

36 FS set button

This pushbutton switch is used when setting the fail

safe servo position.

When this button is pressed when the

function select switch

[35]

on the trim-

mer panel [38] at the back of the trans-

mitter is set to the FS ALL or FS

SELECT position and the transmitter

sticks are set to the desired servo posi-

tions, the transmitter memorizes those

servo positions and simultaneously

Fjg, 27 signals to the receiver.

FS.SET

Since this data is automatically trans-

mitted every 60 seconds thereafter,

pressing the button at every flight is

unnecessary. After the servo position

data has been set, set switch [35] to the

OFF position to prevent erroneous

setting.

During fail safe data transmission, lamp

[A] of monitor lamps

[24]

goes out mo-

mentarily and transmission of the data

is then confirmed.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FP8SSHP Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info