Bedienungsanleitung Futaba FX22 (Seite 50 von 174) (Englisch)

747921

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

ŏ Select the function name

and return to the System

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

Mode and switch selection

1. Access the setup screen page 4 shown

below by touching the S1 button three times.

2. Move the cursor to the [ACT] or [16/12/8CH]

item and touch the RTN button to switch to

the data input mode.

3. Select the mode by scrolling the touch

sensor. The display blinks. Touch the RTN

button to change the mode. (To terminate

the mode change, touch the S1 button.)

"ACT": Enable operation by changing to [OFF]

or [ON].

"16/12/8 CH": When the student uses the FX-

22, T18M=, select [16CH]. When the student

uses the T14M=, T12=, T12FG or FX-40, select

[12CH]. Otherwise select [8CH].

If changing the trainer switch:

4. Move the cursor to the [SW] item and touch

the RTN button to access the switch setup

screen.

(See "Switch selection method" at the end of

this manual for selection method details.)

"SW": Select the desired switch.

Initial setting: SH

*The switch mode can also be selected when setting the ON

position on the switch setup screen. When [ALTERNATE

OFF] is selected, normal ON/OFF operation is performed.

When [ALTERNATE ON] is selected, the trainer function

is alternately turned on and off each time the switch is

operated. This allows alternate ON/OFF switching even

when a momentary switch (SH) is used.

ŏ Select [TRAINER] in the System menu and enter the

setup screen shown below by touching the RTN

button.

Note: The trainer function won’t be turned

on unless the Instructor's transmitter receives

signals from the student's transmitter. Be

sure to confirm this after connecting your

trainer cable.

Operating mode selection

(Setup screen page 1-3)

1. Move the cursor to the [MODE] item of the

channel you want to change and touch the

RTN button to switch to the data input mode.

2. Select the mode by scrolling the touch

sensor. The display blinks. Touch the RTN

button to change the mode. (To terminate

the mode change, touch the S1 button.)

"MODE": Select the desired operation mode

for each channel.

NORM: The model is controlled by signals from the student

transmitter.

MIX mode: The model is controlled by signals from the

instructor and student transmitters. (Reset the student's

model data to the default condition.)

FUNC mode (function mode): The model is controlled by

signals from the student transmitter with the instructor 's

setting. (Reset the student's model data to the default

condition.)

OFF: Only the instructor side operates.

Adjusting the student's rate.

*This can be adjusted for students who may need lower rates

than a more experienced student.

Scrolling

ŏ Moving cursor

ŏ Selecting mode

ŏ Adjusting value

ŏ To next page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 50

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info