Bedienungsanleitung Futaba FX22 (Seite 71 von 174) (Englisch)

747921

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

ŏ Select the function name

and return to the Linkage

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

System Type selection

The FX-22 is for 2.4GHz only. The system can

be changed from among 5 choices: FASSTest

14CH, FASSTest 12CH, FASST MULTI,

FASST 7CH, S-FHSS. It is FASSTest14CH and

FASSTest12CH which can be chosen by R7008SB

set. The method of selection is to the next page.

*If you change the System Type, other model data is not

reset.

*If a system type is changed in helicopter mode, the

transmitter will offer two selections:

[Yes] : Selection sets the channel order suitable for System

Type. (We recommend here. )

[No] : The present channel order is maintained.

*After any change, remember to test the model and should

fully check servo direction and a motion.

*Analog servos cannot be used with the R7008SB in the

SYSTEM

System mode setting, Receiver link

Area mode selection (Frequency range)

The FX-22 transmitter has been designed to

function in many countries. If you will be utilizing

this transmitter in a country other than France,

please make sure that [AREA] is set to "G". If,

however, this transmitter will be utilized in France,

it must be set to "F" in order to comply with French

regulations.FASST mode selection

Receiver linking

The receiver will only be controlled (without

being affected by other transmitters) by the

transmitter it is linked to. When using a receiver

other than one purchased as a set, linking is

necessary.

Moreover, a re-link is required when a new

model is added by model selection, and the time of

system type change.

FASSTest 12CH mode.

Dual receiver function (only FASSTest 14CH

mode)

Dual receivers can be linked with the FX-22.

Two receivers are recognized individually by ID

numbers. For example, in R7008SB, CH output

setting function is used, by setting the first as as

"1-8CH", and setting the second as "9-14CH", two

sets of receivers can be used as a set in the model,

allowing you 14 channels. If a Dual receiver

function is used, the following function can set up

individually.

・

Battery fail-safe voltage setup

A telemetry function cannot be used for the 2nd

receiver.

The voltage and Ext voltage of a 2nd

receiver cannot be known with a transmitter.

Battery fail-safe voltage setup (only FASSTest

mode)

The voltage which battery fail-safe activates,

can be set when you link. (3.5-8.4V) The receiver

memorizes the setting as it was at link.

Suggested setting voltages are as follows.

• 4 cells NiCd or NiMH (Normal: 4.8v) = 3.8 v

• 2 cells LiFe (Normal: 6.6 v) = 6.0 ~ 6.2 v

• 2 cells LiPo (Normal: 7.4 v) = 7.2 ~ 7.4 v

It is a rough reference value.

Since it changes with servos carried in the

condition and the model of a battery, please set to

your own model in a battery consumption current.

ŏ Select [SYSTEM] in the Linkage menu and access

the setup screen shown below by touching the

RTN button.

Scrolling

ŏ Moving cursor

ŏ Selecting mode

P.35

Linking method

Cases when linking is necessary:

・

When using a receiver other than the initial setting.

・

When the communication system was changed.

(FASSTest14CH

↔

FASSTest12CH etc.

)

・

When a new model was created by model

selection.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 71

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info