Bedienungsanleitung Futaba FX22 (Seite 74 von 174) (Englisch)

747921

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

ŏ Select the function name

and return to the Linkage

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

FUNCTION

Channel assignment of each function can be changed.

When you select model and wing (swash) types,

you will find that the optimized combinations of

servo output channels and functions have been

already preset. If you would like, you can freely

change combinations of servo output channels,

functions (aileron, elevator, etc), and control (sticks,

switches, and trim levers).

*You can also assign the same function to multiple servo

output channels such as assigning elevator function to CH2

and CH3.

Channel Replacement

When the channel is replaced in the Function

menu, replaced channel uses the setting data (ATV,

SUB-TRIM, REVERSE, F/S, and B-F/S, etc.).

Servo Output Channels

For FASSTest 14CH mode, you can set 12 linear

channels and two digital channels. For FASSTest

12CH mode, you can set 10 linear channels and

two digital channels. For FASST MULT mode, you

can set 12 linear channels and two digital channels.

Function change

1. Move the cursor to the function item of the

channel you want to change and touch the

RTN button.

*The function selection screen is displayed.

2. Move the cursor to the function name you

want to set and touch the RTN button.

*The function name blinks.

3. Touch the RTN button to execute the

change. (When you want to cancel this

operation, touch the S1 button.)

*Multiple channels can be assigned to one function.

For FASST 7CH mode, you can set only 7 linear

channels. For S-FHSS mode, you can set only 8

linear channels.

*DG1/2 (digital channels)

These channels can function as switched channels. You can

freely change combinations between servo output channels

and input controls (sticks, switches, and trim levers).

Motor Function

If you have either a Glider or Airplane Model

Type selected, and choose to activate the Motor

function, a reverse setting screen is displayed.

*If YES is selected, the output is reversed. If NO is selected,

the output is normal.

:DUQLQJ

As a safety precaution to prevent the motor

from starting unexpectedly, please switch

off the motor accordingly. We also suggest

removing the propeller from the motor as an

additional precaution.

Operation control change

1. Move the cursor to the "CTRL" item of the

channel you want to change and touch the

RTN button.

*The control selection screen is displayed.

2. Move the cursor to the control you want to

change, and touch the RTN button.

*The same control can be assigned to multiple channels.

(The display screen is an example. The

screen depends on the model type.)

ŏ Select [FUNCTION] in the Linkage menu and

access the setup screen shown below by touching

the RTN button.

ŏ Trim operation mode

"COMB": Combination mode

"SEPAR": Separate mode

It sets up by T1-T4 SET of LINKAGE MENU.

Scrolling

ŏ Moving cursor

ŏ Selecting mode

ŏ Adjusting value

ŏ To next page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 74

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info