Bedienungsanleitung Futaba FX22 (Seite 78 von 174) (Englisch)

747921

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

ŏ Select the function name

and return to the Linkage

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

FAIL SAFE

Sets the servos operating position when transmitter signals can no

longer be received or when the receiver battery voltage drops.

(The display screen is an example. The

screen depends on the model type.)

The Failsafe function may be used to set up

positions that the servos move to in the case of

radio interference.

You may set either of two positions for each

channel: Hold, where the servo maintains its last

commanded position, or failsafe, where each

servo moves to a predetermined position. You may

choose either mode for each channel. (FASST 7CH

mode: CH3 only)

The FX-22 system also provides you with an

advanced battery monitoring function that warns

you when the receiver battery has only a little

power remaining. In this case, each servo is moved

to the defined failsafe position. (FASST 7CH

mode: CH3 only) The battery failsafe may be

released by operating a predefined control on the

transmitter (default is throttle), do not continue

to fly, land as soon as possible. Remember, if the

Fail safe setting procedure

1. Move the cursor to the "F/S" item of the

channel you want to set and touch the RTN

button to switch to the data input mode.

2. Select the F/S mode by scrolling the touch

sensor. A conÀrmation message appears.

*The display blinks.

3. Touch the RTN button. (Touch the S1 button

to stop setting.)

*The channel switches to the F/S mode.

4. Move the cursor to the "POS" item.

Hold the corresponding stick, knob, slider,

etc. in the position you want the servo

to move to when the fail safe function is

activated and touch the RTN button for one

second.

*The set position is displayed in percentage.

*If you want to return that channel to the hold mode, move

the cursor to the "F/S" item and touch the RTN button

to switch to the data input mode. Select the F/S mode by

VFUROOLQJWKHWRXFKVHQVRU$FRQ¿UPDWLRQPHVVDJHDSSHDUV

and then change the mode by touching the RTN button.

predefined control suddenly moves to a position

you did not command, land at once and check your

receiver battery.

'H¿QHVVHUYRSRVLWLRQZKHQVLJQDOVDUHORVWDQG

when receiver battery voltage becomes low.

:DUQLQJ

For safety, always set the fail safe functions.

Ɣ5HPHPEHUWRVHWWKHWKURWWOHFKDQQHOIDLOVDIHIXQFWLRQVRWKDW

the servo moves to the maximum slow side for airplanes and

to the slow side from the hovering position for helicopters.

Crashing of the model at full high when normal radio waves

cannot be received due to interference, etc., is very dangerous.

Ɣ,IWKHEDWWHU\IDLOVDIHLVUHVHWE\WKHWKURWWOHVWLFNLWPD\

be mistaken for an engine malfunction and will be reset at

WKURWWOHVORZDQGWKHPRGHOZLOOFRQWLQXHWRÀ\,I\RXKDYH

any doubts, immediately land.

Battery fail safe setting procedure

Battery fail safe can be set for each channel

by the same method as the fail safe setting

procedure. Select and set the "B.F/S" item.

[ON]: Battery fail safe function ON

[OFF]: Battery fail safe function OFF

Battery fail safe release switch setting

This function temporarily releases the battery

fail safe function, so the fuselage can

recover after the battery fail safe function

was activated by a drop in the receiver

battery voltage. This setting selects the switch

which releases the battery fail safe function.

1. Move the cursor to the [RELEASE B.F/S] item in

the setup screen (last page).

2. Touch the RTN button.

*The switch selection screen is called.

*For a detailed description of the switch selection and ON/

OFF direction setting method, see [Switch Setting Method]

at the back of this manual.

ŏ Select [FAIL SAFE] in the Linkage menu and access

the setup screen shown below by touching the

RTN button.

Scrolling

ŏ Moving cursor

ŏ Selecting mode

ŏ Adjusting value

ŏ To next page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info