Bedienungsanleitung Futaba FX22 (Seite 81 von 174) (Englisch)

747921

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

ŏ Select the function name

and return to the Linkage

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

THR CUT

Stops the engine safely and easily.(airplane and helicopter only)

Throttle cut provides an easy way to stop the

engine. Generally speaking, modelers will do so

E\ÀLSSLQJDVZLWFKZLWKWKHWKURWWOHVWLFNDWLGOH

The action is not functional at high throttle to

avoid accidental dead stick landings. The switch’s

location and direction must be chosen, as it defaults

to NULL.

Individually adjust the throttle cut activation

setting for each condition. (helicopter)

Throttle cut setting procedure

1. Activate the function:

Move the cursor to the [ACT] item and touch

the RTN button to switch to the data input

mode.

Select the ACT mode by scrolling the touch

sensor.

*The display blinks.

Touch the RTN button to activate the

function and return to the cursor mode.

2. Switch selection:

Move the cursor to the [SW] item and access

the switch setup screen by touching the

RTN button and select the switch and ON

direction.

*For a detailed description of the setting method, see [Switch

Setting Method] at the back of this manual.

3. Throttle cut position setting:

Move the cursor to the [POS] item and touch

the RTN button to switch to the data input

mode.

Adjust the servo operation position at throttle

cut operation by scrolling the touch sensor.

Initial value: 17

Adjustment range: 0~50

*When the RTN button is touched for one second, the servo

operation position is reset to the initial value.)

Touch the RTN button to end the adjustment

and return to the cursor mode.

*With the selected cut switch ON and the throttle stick at idle;

adjust the rate until the engine consistently cuts off.

However, be sure that the throttle linkage is not pulled too

tight or unreasonable force is not applied to the servo.

Designating a throttle cut setting position.

(helicopter)

*A throttle cut function acts in the low side of the throttle

position.

*"THRO" setting is common with all condition.

:DUQLQJ

Normal setting is slightly above idle.

1. To add the throttle cut position, use the

cursor to select the THRO percentage

desired, then press and hold the RTN button

for one second.

*Since conditions are not offered when an airplane is selected,

the throttle cut options will vary from the options noted

below.

*The throttle cut POS and SW settings are utilized for all

conditions.

*If the throttle cut switch is activated, or on, this status will

continue even if the condition is changed to an inhibited

setting.

*If the condition is inhibited (INH) the throttle cut is off if the

SW is in the off position and the throttle stick is low.

ŏ Select [THR CUT] in the Linkage menu and access

the setup screen shown below by touching the

RTN button.

ŏ Current throttle position

ŏ Individually adjust the Throttle Cut activation

setting for each condition. (helicopter)

ŏ Cut position

Scrolling

ŏ Moving cursor

ŏ Selecting mode

ŏ Adjusting value

ŏ Throttle

cut status

ŏ Throttle

cut status

ŏ Throttle

stick position

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 81

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info