Bedienungsanleitung Futaba FX22 (Seite 84 von 174) (Englisch)

747921

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

ŏ Select the function name

and return to the Linkage

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

6:$6+

Swash AFR and linkage correction function. (helicopter only, except

swash type H-1)

Neutral Point

At your linkages, if the servo horn deviates from

a perpendicular position at neutral, the linkage

compensation functions in this menu may not

compensate effectively. To correct this use the

Neutral Point function. This will move the neutral

point of the servos to the actual perpendicular

position. However, this adjustment changes only

the axis point of the compensation functions in this

menu, and does not affect the neutral position of

other functions.

Swash AFR

Swash AFR function reduces, increases, or

reverses the rate (travel) of the aileron, elevator and

collective pitch functions, by adjusting or reversing

the motion of all servos involved in that function,

only when using that function.

Mixing Rate

This mixing is used to compensate the swash-

plate as necessary during specific control inputs.

Neutral point setting procedure

The neutral point becomes the correction

standard point.

*Adjusting the servo horn so that the neutral point is near the

50% position makes the mixing amount small.

1. Neutral point setting

Move the cursor to the [POS] item and hold

the pitch operation so that the servo horn is

at a right angle to the linkage rod and Touch

the RTN button for one second. This value

indicates the servo's neutral position.

After reading the neutral point, use the

other correction functions to make further

adjustments.

The following compensation mixing is possible;

PIT to AIL, PIT to ELE, AIL to PIT, ELE to AIL,

and ELE to PIT (HR3 mode.) It adjusts the swash-

plate to for proper operation of each control using

the corresponding compensation mixing.

Linkage Compensation

This compensation mixing is used to correct the

swash-plate for pitch control at low pitch and high

pitch.

Speed Compensation

This function is used to cancel the reaction that

is generated by the difference in the movements of

each servo when the swash-plate moves.

Subtrim

Subtrim for aileron, elevator and pitch can be set

during swash setting.

Pitch adjustment function

+LJKQHXWUDODQGORZSLWFK¿[HGRXWSXWVFDQEH

used while adjusting the pitch.

Swash AFR setting procedure

The swash AFR function makes adjustments so

WKDWWKHVHUYRVWUDYHOWKHVSHFL¿HGDPRXQWE\>$,/@

[ELE], and [PIT] operation.

1. Move the cursor to the function you want to

adjust and touch the RTN button to switch to

the data input mode.

2. Adjust the AFR rate by scrolling the touch

sensor.

Initial value: 50

Adjustment range: -100~100

*When the RTN button is touched for one second, the AFR

rate is reset to the initial value.

Touch the RTN button to end adjustment and

return to the cursor mode.

ŏ Select [SWASH] in the Linkage menu and access

the setup screen shown below by touching the

RTN button.

Scrolling

ŏ Moving cursor

ŏ Selecting mode

ŏ Adjusting value

ŏ To next page

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 84

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info