Bedienungsanleitung Futaba FX22 (Seite 149 von 174) (Englisch)

747921

149

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

149

ŏ Select the function name

and return to the Model

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

PIT CURVE/PIT TRIM

Pitch Curve

This function adjusts the pitch operation curve

for each flight condition to optmize the model's

performance in relationship to the throttle stick position.

$VLPSOHFXUYHFDQEHFUHDWHGE\UHGXFLQJWKHQXPEHURI

LQSXWSRLQWVWRWZRRUWKUHHDQGWKHQHQWHULQJWKHVSHFL¿HG

value at the corresponding points.

Normal curve adjustment

)RUQRUPDOFXUYHFUHDWHDEDVLFSLWFKFXUYHFHQWHUHG

DERXWKRYHULQJ8VHWKLVIXQFWLRQWRJHWKHUZLWKWKH7+5

Curve (Normal) function and adjust the curve so that up/

GRZQFRQWUROLVEHVWDWDFRQVWDQWHQJLQHVSHHG

Idle up curve adjustment

*For the high side pitch curve, set the maximum pitch

so that it does not overload the engine. For the low side

pitch curve, create curves matched to loop, roll, 3D, and

other purposes and use the idle up curves according to the

performance.

Throttle hold curve adjustment

*The throttle hold curve is used when executing auto

rotations.

Operation precautions

Warning

When actually starting the engine and flying,

always set the idle up condition switch to OFF

and start the engine at idle.

ŏ Select [PIT CURVE] at the Model menu and access

the setup screen shown below by touching the

RTN button.

ŏ Pitch curve copy

Scrolling

ŏ Moving cursor

ŏ Selecting mode

ŏ Adjusting value

ŏ To next page

(Currently selected condition name)

1. Move the cursor to the curve point setting

item you want to delete/return and touch

the RTN button for one second.

Ɣ3LWFKFXUYHFRS\IXQFWLRQ

Move the cursor to COPY and touch the RTN

button to switch to the data input mode.

Select the copy destination condition by

scrolling the touch sensor and touch the RTN

button. Select the [YES] and touch the RTN

button.

ŏ curve rate

ŏ curve point

Setting method

ƔSRLQWFXUYHVHWWLQJ

[Curve rate setting]

1. Move the cursor to the curve rate setting

item you want to adjust and touch the RTN

button to switch to the data input mode.

Adjust the rate by scrolling the touch sensor.

Initial value: P1: -100, P2: -50, P3: 0, P4:

50, P5: 100

Adjustment range: -100~100

:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV

reset to the initial value.

Touch the RTN button to end the adjustment

and return to the cursor mode.

2. Repeat this procedure for each point as

desired.

[Moving curve point]

1. Move the cursor to the curve point setting

item you want to adjust and touch the RTN

button to switch to the data input mode.

Adjust the curve point by scrolling the touch

sensor.

Initial value: P1: (0), P2: 25, P3: 50, P4:

75, P5: (100)

Adjustment range: Up to 2.5 in front of the

adjoining point

:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHFXUYH

position is reset to the initial value.)

Touch the RTN button to end the adjustment

and return to the cursor mode.

2. Repeat this procedure for each point as

desired.

[Deleting/returning curve point]

*The graph display includes the pitch

trim operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 149

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info