Bedienungsanleitung Futaba FX22 (Seite 158 von 174) (Englisch)

747921

158

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

158

ŏ Select the function name

and return to the Model

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

PIT to RUD mixing (Revolution mixing)

Use this mix when you want to suppress the

UHDFWLRQWRUTXHJHQHUDWHGE\PDLQURWRUSLWFKDQG

speed changes during pitch operation. Adjust so

that the nose does not move in the rudder direction.

The mixing curve rate should be started

using smaller values.

For a rotor with a clockwise operation

direction, when pitch was input at the plus

side, set these parameters so that mixing

is in the clockwise direction. First, trim at

hovering and then adjust the neutral

position.

1. Adjustment between slow and hovering

Repeatedly hover from take off and land

at a constant rate matched to your own

rhythm. Then adjust the pitch so that the

nose of the helicopter remains steady

when the throttle is raised and lowered.

2. Throttle high side (climbing and diving from

hovering)

Repeat climbing and diving from hovering

at a constant rate matched to your own

rhythm and adjust the pitch so that the nose

does not deflect when the throttle is raised

and lowered.

Note: When a GY Series or other heading hold

gyro is used, since correction is performed by

the gyro, this mix is not utilized. If this function

is used when the gyro operation mode is the

AVCS mode, the neutral position will change.

Set the mixing rate so that the rudder direction

at high-speed Áight is straight ahead. Adjust for

each condition used.

ŏ Select [PIT to RUD] at the Model menu and access

the setup screen shown below by touching the

RTN button.

(Currently selected condition name)

Scrolling

ŏ Moving cursor

ŏ Selecting mode

ŏ Adjusting value

ŏ To next page

Setting method

Ɣ$FWLYDWHWKHPL[LQJ

When using this function, move the cursor to

the [ACT] item and touch the RTN button to

switch to the data input mode.

Select the ACT mode by scrolling the touch

sensor.

7KHGLVSOD\EOLQNV

Touch the RTN button to activate the mixing

and return to the cursor mode. (ON is

displayed.)

ƔSRLQWFXUYHVHWWLQJ

Move the cursor to the curve rate setting

item you want to adjust and touch the RTN

button to switch to the data input mode.

Adjust the rate by scrolling the touch sensor.

Initial value: P1~P5: 0

Adjustment range: -100~100

:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKHUDWHLV

reset to the initial value.)

Touch the RTN button to end the adjustment

and return to the cursor mode.

Repeat this procedure for each point.

Ɣ3LWFKFXUYHFRS\IXQFWLRQ

Move the cursor to COPY item and touch the

RTN button to switch to the data input mode.

Select the copy destination condition by

scrolling the touch sensor and touch the RTN

button. Select the [YES] and touch the RTN

button.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 158

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info