Bedienungsanleitung Futaba FX22 (Seite 162 von 174) (Englisch)

747921

162

Zoom out

Zoom in

Vorherige Seite

1/174

Nächste Seite

162

ŏ Select the function name

and return to the Model

menu by touching the

RTN button or pushing the

HOME/EXIT button.

<SensorTouch™>

RETURN

GOVERNOR mixing

:KHQXVLQJD)XWDED*9*<&*<

JRYHUQRUWKLVIXQFWLRQLVXVHGWRVZLWFKWKH530

of the helicopter's rotor head. The rotor head speed

FDQEHVZLWFKHGZLWKHDFKFRQGLWLRQRUWKHVZLWFK

7KHJRYHUQRULVXVHGE\FRQQHFWLQJWKHJRYHUQRUVSHHG

VHWWLQJFKDQQHOWR&+LQLWLDOVHWWLQJ

*When using an independent governor [ON]/[OFF] switch,

connect the AUX([ON]/[OFF]) connector of the governor to

&+DQGVHWWKHVZLWFKWR&+*RYHUQRUDWWKH)XQFWLRQ

menu of the Linkage Menu.

Note: Always set (Control) and (Trim) to [--]

for [Governor] of the Function menu of the

Linkage menu.

ŏ Select [GOVERNOR] at the Model menu and access

the setup screen shown below by touching the RTN

button.

Scrolling

ŏ Moving cursor

ŏ Selecting mode

ŏ Adjusting value

ŏ To next page

(Currently selected condition name)

ŏUnit display selection:

[]/[rpm]

ŏSetup screen selection

ŏACT/INH: INH (initial setting)

ŏFine tuning VR settings

ŏRPM adjustment

ŏCondition/Switch selection

Setting method

Ɣ$FWLYDWHWKHPL[LQJ

When using this function, move the cursor to

the [INH] item and touch the RTN button to

switch to the data input mode.

Select the ACT mode by scrolling the touch

sensor.

7KHGLVSOD\EOLQNV

Touch the RTN button to activate the mixing

and return to the cursor mode. (ON is

displayed.)

When the Governor is changed from the

default inhibited (INH) state to the active

(ACT) state, the endpoint menu will be

displayed and it is possible to utilize the

endpoints for this given condition.

*When the function is set ON/OFF at the governor setup

screen, the governor rpm setting channel end point servo

travel and limit point are now initialized.

:KHQFKDQJHGIURP,1+WR$&721WKHVHUYRWUDYHOLV

initialized to 100 and the limit point is initialized to 155.

:KHQRSHUDWLRQLVFKDQJHGWR,1+DWDOOFRQGLWLRQVWKH

servo travel is initialized to 100 and the limit point is

initialized to 135.

Use the SensorTouch to scroll to either YES

(incorporate the default endpoints) or NO

(endpoints are not utilized. Press the Return

(RTN) button to conÀrm the selection made.

Ɣ530DGMXVWPHQW

Move the cursor to the rate item and touch

the RTN button to switch to the data input

mode.

Adjust the rpm by scrolling the touch sensor.

Initial value: 50 (1500rpm)

Adjustment range: OFF, 0~110 (OFF,

700~3500rpm)

:KHQWKH571EXWWRQLVWRXFKHGIRURQHVHFRQGWKH

sensitivity is reset to the initial value.)

Touch the RTN button to return to the cursor

mode.

Ɣ8QLWGLSOD\VHOHFWLRQ

Move the cursor to the UNIT item and touch

the RTN button to switch to the data input

mode. Select the unit by scrolling the touch

sensor.

Touch the RTN button to change the

operation mode and return to the cursor

mode.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba FX22 Seite 162

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info