747977

Futaba GYD450 Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
WARNING
Failure to follow these safety precautions may result in severe injury to
yourself and others.
Check that there is sufficient battery capacity.
Do not operate the model and transmitter steering wheel
for about 3-5 seconds after turning on the GYD450 (When
shared with the receiver).
• GYD450 initialization and neutral position reading. The GYD450 is initialized when the
power is turned on. The neutral position is also read at the same time. If initialization
ends normally, the operator is informed by two repetitive movements of the servo to
the left and right (a little).
Always check the direction of operation of the gyro.
Do not strike the gyro with a hard object. Do not drop it onto
a concrete surface or other hard floor.
• The sensor may become damaged during strong impacts.
Do not use trims or mixing.
• All corrections are made by the gyro. Therefore, if trimming and mixing, are turned on,
operation will be the same as deviating from the neutral position.
Do not use the GYD450 for applications other than RC cars.
•This gyro is designed for RC cars only. Do not use it for other applications.
Analog servos cannot be used.
•The use of analog servos may cause servo trouble.
Do not place gyro near heating equipment (engine, motor,
ESC, battery, servo, etc.).
• Always allow the gyro to adjust to the surrounding environmental temperature before
ÀLJKW$ODUJHWHPSHUDWXUHFKDQJHGXULQJXVHZLOOFDXVHGULIWDQGRWKHURSHUDWLRQDO
issues.
Connecting the GYD450 S.BUS Connecting the GYD450
Mounting to Chassis
Steering servo SR mode
Rate Gyro
for RC Drift Cars
I
NSTRUCTION
M
ANUAL
I
NSTRUCTION
M
ANUAL
Only for Futaba digital servo
For RC models
Gyro
Included sponge
sensor tape
Degrease
and stick
Horizontal plane
Flat surface of the chassis where the sensor
tape sticks easily. Mount the gyro level so
that it is not tilted relative to the chassis.
Use the included double-sided sponge tape to firmly at-
tach the gyro perpendicular to the control axis, at a posi-
tion where there is as little vibration as possible. Make the
Gyro mounting position
The direction of rotation fixed by the gyro can be any
direction within 360° relative to the steering axis controlled
by the gyro.
• No part of this manual may be reproduced in any form without prior permis-
sion.
• The contents of this manual are subject to change without prior notice.
• Futaba is not liable for any potential damage (accidental or otherwise) that
may occur after installation.
Before using your new gyro, please read this manual thoroughly and
use the gyro properly and safely. After reading this manual, store it in
a safe place.
● Dedicated RC Drift car setting
Vehicle straight-line and cornering performance can be increased without
taking into account the effect of the road surface, etc.
● Remote gain function and mode switching function
You can adjust gain from the transmitter (3 or more CH) by using the
remote gain function. Gain can also be adjusted with the trimmer on the
GYD450. The mode switching function allows AVCS/NORMAL gyro mode
switching.
● Integrated, compact, and light weight
Compact size
（
20.5x20.5x11mm
）
and light weight
（
3.7g
）
realized by
high density mounting technology.
● Easy setup
The GYD450 can be used immediately with minimum setup.
● Supporting the S.BUS/S.BUS2 connection
Only one wire connection to the receiver can operate the GYD450.
● Only for Futaba digital servo
GYD450 Ratings:
(Integrated sensor type rate gyro)
• Gyro sensor: MEMS vibrating structure gyro
• Operating voltage: DC4.2V to 8.4V
• Current drain: 30mA (excluding a servo)
• Operating temperature range: -10ºC to +45ºC
• Dimensions: 20.5 x 20.5 x 11.0mm (0.8 x 0.8 x 0.43in) (except protrusion)
• Weight: 3.7g (0.13oz)
• Functions: Sensitivity trimmer. LED monitor. Servo selection (SR mode
ON/OFF). S.BUS/S.BUS2 connection.
Features of GYD450
Functions
Monitor LED display
State Color Move Reference
1. No servo pulse / sensor
error
Red 2 flash
2. Warm-up Green Fast blink
3. Sensor initialization Red/Green ON
AVCS (Red)
NORMAL (Green)
4. Turn Red/Green Fast blink
Right (Green)
Left (Red)
5. Neutral offset Orange Slow blink Stick operation
6. Gain OFF
−
OFF
7. Switch operation Green One blink
Each time of switch
operation
8. Low battery Red One flash Less than 4.0V
●
Trimmer
（
Limit/Gain
）
●
LED
●
Servo selection switch
(SR mode ON/OFF)
●
Port1
（
Steering input/
S.BUS input
）
●
Port2
（
Gain input
）
●
Port3
（
Steering servo output
）
●
Gyro direction
Switch
Set Contents
The following items are supplied with the GYD450:
Mini screwdriver
Sensor tape
Extension cord
Nylon strap
GYD450
1M23N33302
Thank you for purchasing the
GYD450 RC cars gyro. Compact
and lightweight, the GYD450 is
designed to control steering for RC
Drift cars. If the transmitter has 3
or more channels (capable of 3CH
adjustment) the gyro sensitivity can
be adjusted from the transmitter.
Features include simple set-up and
S.BUS/S.BUS2 connectivity.
S.BUS/S.BUS2 port
GYD450 GYD450
S.BUS Receiver
Steering servo Steering servo
Steering CH1
Gyro gain CH3
Receiver
Gyro gain CH(Receiver)←connect→Port2(GYD450)
Remote gain effective. Trimmer(GYD450) becomes LIMIT.
Gyro gain CH(Receiver)←It does not connect→Port2(GYD450)
Remote gain is invalid. Trimmer(GYD450) becomes GAIN.
S.BUS CH
Steering --- 1CH
Gyro gain --- 3CH
Extension cord
In S.BUS
connection, the
port 2 is not
connected.
Remote gain is still
effective.
wiring loose and bundle it with the included nylon strap so
that it will not interfere with the rod.
Link the servo in accordance with the kit instruction man-
ual. Adjust the linkage rod so that the trim amount is as
small as possible.
When using S.BUS servo, initialize a parameter.
Make the servo operating range as wide as possible.
Make the numerical value of EPA (ATV) equally in left and
right.
It is possible when using the T7PX to change the servo to
"SR Mode" and improve the servo response. If the servo
can't be changed to SR mode, do not set the TX to SR
mode.
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Futaba GYD450 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info