Bedienungsanleitung Futaba R202GF (Seite 1 von 1) (Englisch)

747964

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation, model number R202GF, complies with part15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@hobbico.com (Support)

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

©FUTABA CORPORATION 2015, 5 (1)

R202GF Speciﬁcations:

(

S-FHSS/FHSS

system, 2-channel receiver)

• Receiving on 2.4GHz band

• System:

S-FHSS/FHSS

system (auto detection)

S-FHSS

Normal/High speed mode (auto detection)

•

Operating voltage(Typ.): 4.8V-7.4V(

shared with servo)

• F/S and Battery F/S function: The operation channels differ according to the transmitter used. However, Battery

F/S doesn't function when it is used with FHSS and F/S becomes only CH2.

• Battery F/S voltage: 3.8V

• Current drain: 30mA (at no signal)

• Size: 0.9x1.4x0.4” (23x35x9mm)

• Weight: 0.2 oz. (6g)

The Battery F/S voltage is set for 4-cell NiCd/NiMH battery. Battery F/S function doesn't work

properly when other type battery is used.

WARNING

NEVER use dry batteries for the

power supply of the R202GF as they

may cause difﬁculties.

Link Procedure

Each transmitter has an individually assigned,

unique ID code. In order to start operation, the

receiver must be linked with the ID code of the

transmitter with which it is being paired. Once the

link is made, the ID code is stored in the receiver

and no further linking is necessary unless the

receiver is to be used with another transmitter.

Place the transmitter and the receiver close

to each other within half (0.5) meter

Turn on the transmitter and the receiver.

Push and hold the Link switch on the

receiver.

When the link is complete, the LED on the

receiver changes to solid green.

* Please refer to the table below for LED status

and receiver condition.

No signal reception LED: Off

Receiving signals LED: On

Receiving signals, but ID

is unmatched.

LED: Blink

Power On, when F/S

sets it.

LED: Early

Blink the ﬁrst

one second

* If there are many

S-FHSS/FHSS

systems turned

on around your receiver, it might not link to your

transmitter. In this case, even if the receiver’s

LED stays solid green, unfortunately the

receiver might have established a link to one of

the other transmitters. This is very dangerous

if you do not notice this situation. In order to

avoid the problem, we strongly recommend

you to double-check whether your receiver is

controlled by your transmitter by giving throttle

input, etc. and then checking servo response.

WARNING

After the linking is done, please cycle

receiver power and check if the receiver

to be linked is really under the control by the

transmitter to be linked.

Do not perform the linking procedure

with motor's main wire connected or

with the engine operating as it may result in

serious injury.

Link switchLED

Battery terminal (B)

CH output (1 / 2)

Operating Precautions:

Once the

R202GF

detects the

S-FHSS

normal mode,

S-FHSS

high speed

mode or

FHSS

mode, the detected

mode is locked as long as the

power is ON. When need to change

the mode, please cycle power.

Note:

The R202GF is compatible with the S-FHSS or FHSS

system transmitters .

*Futaba S-FHSS/FHSS system does not work with current Futaba FASST/T-FHSS

system.

Usage condition on "High Speed mode"

CAUTION

When using the high-speed mode, use a Futaba digital

servo (including brushless servo). Analog servos

cannot be used.

• The use of analog servos may cause servo trouble.

1M23N17486

S-FHSS/FHSS-2.4GHz

system

(Auto Detection),

2-channel receiver

Thank you for purchasing the

R202GF

receiver.

The

R202GF

is designed for use with the Futaba

S-FHSS

FHSS

system transmitter. The

S-FHSS

system has two(2) operation mode as shown below.

•Normal mode/High Speed mode

The "Normal mode" accepts any type of servos or the

peripherals as the frame rate of the output is 13.6ms.

The "High Speed mode" only accepts the digital

servos, including BLS series, and most peripheral

equipments such as the brushless ESCs. The frame

rate of the outputs is 6.8ms. However, there is a

transmitter that cannot correspond, too.

Please pay special attention to the information

contained within this manual and transmitter's manual

LQRUGHUWRKDYHDSOHDVDQWUXQQLQJÀ\LQJH[SHULHQFH

The R202GF is compatible with the S-FHSS or FHSS

system transmitters

R202GF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba R202GF Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info