Bedienungsanleitung Futaba R2104GF (Seite 1 von 1) (Englisch)

747948

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

R2104GF

S-FHSS/FHSS-2.4GHz system

(Auto Detection),

4-channel receiver

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of America, model number R2104GF, complies

with part15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause

undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

Thank you for purchasing the

R2104GF

receiver.

The

R2104GF

is designed for use with the Futaba

S-FHSS

FHSS

system transmitter. The

S-FHSS

system has two(2) operation mode as shown below.

s.ORMALMODE(IGH3PEEDMODE

The "Normal mode" accepts any type of servos

or the peripherals as the frame rate of the output

is 13.6ms. The "High Speed mode" only accepts

the digital servos, including BLS series, and most

peripheral equipments such as the brushless ESCs.

The frame rate of the outputs is 6.8ms.

Please pay special attention to the information

contained within this manual and transmitter's

manual in order to have a pleasant running/ﬂying

experience.

The

R2104GF

is compatible with the

S-FHSS

FHSS

system transmitters as shown "Transmitter

and Receiver Compatibility".

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

1M23N17432 ©FUTABA CORPORATION 2010, 8 (1)

2'&3PECIlCATIONS

(

S-FHSS/FHSS

system, 4-channel receiver)

s2ECEIVINGON'(ZBAND

s3YSTEM

S-FHSS/FHSS

SYSTEMAUTODETECTION

s/PERATIONMODE.ORMAL(IGHSPEEDAUTODETECTION

s0OWERREQUIREMENT6OR6SHAREDWITHSERVO

s#URRENTDRAINM!ATNOSIGNAL

s3IZEXXvXXMM

s7EIGHTOZG

ｎ

WARNING

ｌ

.%6%2USEDRYBATTERIESFOR

THEPOWERSUPPLYOFTHER2104GF

ASTHEYMAYCAUSEDIFlCULTIES

Link Procedure

Each transmitter has an individually assigned,

unique ID code. In order to start operation, the

receiver must be linked with the ID code of the

transmitter with which it is being paired. Once the

link is made, the ID code is stored in the receiver

and no further linking is necessary unless the

receiver is to be used with another transmitter.

0LACETHETRANSMITTERANDTHERECEIVERCLOSE

TOEACHOTHERWITHINONEMETER

4URNONTHETRANSMITTERANDTHERECEIVER

0USHANDHOLDTHE,INKSWITCHONTHE

RECEIVER

7HENTHELINKISCOMPLETETHE,%$ONTHE

RECEIVERCHANGESTOSOLIDGREEN

0LEASE REFER TO THE TABLEBELOWFOR ,%$ STATUS

ANDRECEIVERCONDITION

.OSIGNALRECEPTION 2ED/N

2ECEIVINGSIGNALS 'REEN/N

2ECEIVINGSIGNALSBUT)$

ISUNMATCHED

'REEN"LINK

)F THERE ARE MANY

S-FHSS/FHSS

 SYSTEMS TURNED

ONAROUNDYOURRECEIVERITMIGHTNOTLINKTOYOUR

TRANSMITTER )NTHISCASE EVEN IFTHERECEIVERS

,%$STAYSSOLIDGREENUNFORTUNATELYTHE

RECEIVERMIGHTHAVEESTABLISHEDALINKTOONEOF

THE OTHER TRANSMITTERS 4HIS IS VERY DANGEROUS

IFYOU DO NOTNOTICETHISSITUATION  )N ORDERTO

AVOIDTHEPROBLEMWESTRONGLYRECOMMEND

YOUTO DOUBLECHECKWHETHERYOURRECEIVERIS

CONTROLLED BY YOUR TRANSMITTER BY GIVING THROTTLE

INPUTETCANDTHENCHECKINGSERVORESPONSE

ｎ

WARNING

ｊ

!FTERTHELINKINGISDONEPLEASE

CYCLERECEIVERPOWERANDCHECKIF

THERECEIVERTOBELINKEDISREALLYUNDERTHE

CONTROLBYTHETRANSMITTERTOBELINKED

ｌ

$ONOTPERFORMTHELINKINGPROCEDURE

WITHMOTORgSMAINWIRECONNECTEDOR

WITHTHEENGINEOPERATINGASITMAYRESULTIN

SERIOUSINJURY

FHSS-2.4GHz/S-FHSS-2.4GHz System

Transmitter and Receiver Compatibility

Transmitter

&(33

2ECEIVER

3&(33&(33

2ECEIVER

R603GF

R2004GF

R2104GF

40,'&(33 Okay Okay

&3FUNCTION#H

40,'&(33 Okay Okay

&3FUNCTION#H

49&'&(33 Okay Okay

40,'

3&(33

(IGH3PEED

— Okay

&3FUNCTION!LLCHANNELS

"&3FUNCTION#H

$IGITALSERVOONLYAT(IGH3PEED

MODE

.ORMAL

&(33 Okay Okay

&3FUNCTION#H

Link switch LED

Ch output (1 to 4)

Battery terminal (B)

/PERATING0RECAUTIONS

/NCETHE

R2104GF

DETECTSTHE

S-FHSS

NORMALMODE

S-FHSS

HIGHSPEED

MODEOR

FHSS

MODETHEDETECTED

MODEISLOCKEDASLONGASTHE POWER

IS/.7HENNEEDTOCHANGETHE

MODEPLEASECYCLEPOWER

.OTE&UTABA

FHSS/S-FHSS

SYSTEMAND

FASST

SYSTEMARENOTCOMPATIBLEEACHOTHER

Usage condition on "High Speed mode"

ｎ

CAUTION

ｊ

7HENUSINGTHEHIGHSPEEDMODEUSEA

&UTABADIGITALSERVOINCLUDINGBRUSHLESS

SERVO!NALOGSERVOSCANNOTBEUSED

s4HEUSEOFANALOGSERVOSMAYCAUSESERVOTROUBLE

Futaba R2104GF Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info