Bedienungsanleitung Futaba R304SB (Seite 1 von 2) (Englisch)

747966

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Link Procedure

Each transmitter has an individually

assigned, unique ID code. In order to start

operation, the receiver must be linked

with the ID code of the transmitter with

which it is being paired. Once the link is

made, the ID code is stored in the receiver

and no further linking is necessary unless

the receiver is to be used with another

transmitter.

Place the transmitter and the

receiver close to each other within

half (0.5) meter.

Place the transmitter into the linking

mode, and turn on the receiver.

During countdown, push the receiver

tact switch for approximately 2

seconds. The LED will begin to blink

red. After the receiver LED switches

from blinking red to green

→

red

steady light, If the transmitter and

receiver are linked normally, set the

power switch to the OFF position

and then return it to the PWR ON

position. If the receiver LED lights

green, linking was successful.

Actually check servo operation.

* Please refer to the table below for

LED status and receiver condition.

* Refer to the transmitters operation

manual for complete details on how to

place the transmitter into the linking

mode.

* If there are many T-FHSS systems

turned on in close proximity, your

receiver might have difficulty

establishing a link to your transmitter.

This is a rare occurrence. However,

should another T-FHSS transmitter/

receiver be linking at the same time,

your receiver could link to the wrong

transmitter. This is very dangerous

if you do not notice this situation. In

order to avoid the problem,we strongly

recommend you to double check

whether your receiver is really under

control by your transmitter.

󾛽

WARNING

￸

After the linking is done, please cycle receiver power and check if the

receiver to be linked is really under the control by the transmitter to be linked.

￺

Do not perform the linking procedure with motor's main wire connected or

with the engine operating as it may result in serious injury.

Link switchLED

S.BUS2 / (Battery)

CH output

(1 to 4) / (Battery)

Operating Precautions:

Once the

R304SB

detects the

T-FHSS

normal mode

T-FHSS high

speed mode

, the detected mode is

locked as long as the power is ON.

When need to change the mode,

please cycle power.

Note:

The R304SB is compatible with the T-FHSS system

transmitters.

The receiver type setting of the transmitter is set in T-FHSS.

*Futaba T-FHSS system does not work with current Futaba S-FHSS/FHSS/FASST-

est/FASST system.

Usage condition on "High Speed mode"

󾛽

CAUTION

￸

When using the high-speed mode, use a Futaba digital servo (including

brushless servo). Analog servos cannot be used.

s4HEUSEOFANALOGSERVOSMAYCAUSESERVOTROUBLE

1M23N28502

T-FHSS-2.4GHz System

S.BUS2, 4-Channel

Receiver for Model Car

Thank you for purchasing the

R304SB

receiver. The

R304SB

is designed for use with

the Futaba

T-FHSS

system transmitter.

The

R304SB

receiver has adopted the newly

developed bidirectional communication

system "

T-FHSS

s4ELEMETRYSYSTEM

With the

telemetry system

, the running

status can be displayed at the transmitter.

The telemetry data can be checked at the

transmitter by connecting the

telemetry sensor

sold separately to the

S.BUS2

connector of the

R304SB

receiver.

s.ORMALMODE(IGH3PEEDMODE

The "Normal mode" accepts any type of servos

or the peripheral. The "High Speed mode"

only accepts the digital servos, including BLS

series, and most peripheral equipments such

as the brushless ESCs. Please pay special

attention to the information contained within

this manual and transmitter's manual in order

to have a pleasant running experience.

R304SB

󾛽

WARNING

￺

NEVER use dry batteries for

the power supply of the R304SB

as this may cause difficulties with

the receiver's operation.

￸

Wrap the receiver with

something soft,such as foam

rubber,to avoid vibration. Do not

splash water over the receiver.

￸

Since the receiver generates a

certain amount of heat, install

the place with good ventilation.

No signal recep-

tion

LED: Red

Receiving signals LED: Green

Unrecover-

able failure

(EEPROM,etc.)

LED: Red

and Green

turn on alter-

nately

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba R304SB Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info