Bedienungsanleitung Futaba R334SBS (Seite 1 von 1) (Englisch)

747970

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

Link Procedure

Each transmitter has an individually assigned, unique ID code. In order to start

operation, the receiver must be linked with the ID code of the transmitter with

which it is being paired. Once the link is made, the ID code is stored in the

receiver and no further linking is necessary unless the receiver is to be used with

another transmitter.

Place the transmitter and the receiver within half a meter of each other.

Place the transmitter into the linking mode and turn on the receiver.

During countdown, push the receiver tact switch for approximately 2 seconds.

The LED will begin to blink red. After the receiver LED switches from blinking

red to green

→

green (red) steady light, If the transmitter and receiver are

linked normally, set the power switch to the OFF position and then return it to

the PWR ON position. If the receiver LED lights green, linking was successful.

(T4PLS,T4GRS : set the power switch to the OFF position and then return it to

the PWR ON position.) Actually check servo operation.

* Please refer to the table below for LED status and receiver condition.

* Refer to user manual of the transmitter, to change your transmitter in "Link" mode.

* If there are many T-FHSS systems turned on in close proximity, your receiver might have

difﬁculty establishing a link to your transmitter. This is a rare occurrence. However, should

another T-FHSS transmitter/receiver be linking at the same time, your receiver could link to the

wrong transmitter. This is very dangerous if you do not notice this situation. In order to avoid

the problem,we strongly recommend you double check whether your receiver is really under

control by your transmitter.

WARNING

After the linking is done, please cycle receiver power and check if the receiver

to be linked is really under the control of the transmitter to be linked.

Do not perform the linking procedure with motor's main wire connected or with

the engine operating as it may result in serious injury.

Note: The R334SBS is compatible with the

T-FHSS SR/T-FHSS system transmitters.

The receiver type setting of the transmitter is

set in T-FHSS SR/T-FHSS.

*Futaba T-FHSS system does not work with current

Futaba S-FHSS/FHSS/FASSTest/FASST/T-FHSS Air

system.

Usage condition on "T-FHSS High Speed mode"

CAUTION

When using the high-speed mode, use a Futaba digital servo (including

brushless servo). Analog servos cannot be used.

• The use of analog servos may cause servo trouble.

Usage condition on "T-FHSS SR mode"

CAUTION

When using the T-FHSS SR mode, use an SR mode servo. Nomal servos

cannot be used.

• The use of nomal servos may cause servo trouble.

1M23N17493

T-FHSS SR/T-FHSS-2.4GHz System

Diversity antenna

S.BUS2, 4-Channel Receiver for Model Car

Thank you for purchasing the

R334SBS

receiver. The

R334SBS

is designed for use

with the Futaba

T-FHSS SR/T-FHSS

system

transmitter. The

R334SBS

receiver has

adopted the newly developed high-speed

response system "

T-FHSS SR

• SR servo

The servo corresponding to the SR mode is needed.

The servo type setting of the transmitter is set in SR mode.

• SR mode ON/OFF

ON/OFF of SR mode can be established according to each channel by

a transmitter setting. An OFF channel can use a normal servo/ESC.

• Telemetry function

Telemetry function cannot be used for the T-FHSS SR. Do not use the

S.BUS2 port in SR mode.

• Mode Change

To change the system mode, select the system mode (T-FHSS or

7)+6665RIWKHWUDQVPLWWHU¿UVW

Then, making a link between the transmitter and the receiver to build

up the radio linkage.

T-FHSS Re-Link T-FHSS SR

• Telemetry system

With the

telemetry system

, the running status can be displayed at the

transmitter. By connecting

S.BUS sensors

that are separately sold into

the

S.BUS2

port of the receiver (R334SBS),

the transmitter will be possible to show the telemetry data on its display.

• Normal mode/High Speed mode

The "Normal mode" accepts any type of servos or the peripheral. The

"High Speed mode" only accepts the digital servos, including BLS

series, and most peripheral equipments such as the brushless ESCs.

Please pay special attention to the information contained within this

manual and transmitter's manual in order to have a pleasant running

experience.

Operating Precautions (T-FHSS):

Once the R334SBS detects the T-FHSS normal mode or T-FHSS high

speed mode, the detected mode is locked as long as the power is ON.

When need to change the mode, please cycle power.

R334SBS

WARNING

NEVER remove the case to avoid the unexpected malfunction. When removing

a case from the double-stick tape, maintain the bottom case.

NEVER use dry batteries for the power supply of the R334SBS as this may

cause difﬁculties with the receiver's operation.

Wrap the receiver with something soft, such as foam rubber, to avoid vibration.

Do not splash water over the receiver.

Since the receiver generates a certain amount of heat, install in a place with

good ventilation.

Do not put any conductive equipment/sticker on the antenna part. (Receiver

top)

• Otherwise, the operating range may become shorter.

No signal reception LED: Red

Receiving signals LED: Green

Unrecoverable fail-

ure (EEPROM,etc.)

LED: Red and

Green turn on

alternately

R334SBS Speciﬁcations:

(

T-FHSS

SR/T-FHSS

system,

S.BUS2

, 4-channel receiver)

• Receiving on 2.4GHz band

• System:

T-FHSS SR/T-FHSS

system

•

Power requirement Operating voltage: 3.7V-7.4V

• F/S and Battery F/S function:It is set according to the transmitter used.

• Battery F/S voltage: Set it with the transmitter arbitrarily.

• Size: 1.33x0.88x0.44” (

33.9x22.3x11.3

mm)

• Weight: 0.26oz. (7.5g)

/LQN6ZLWFK岜/('

+8%

%DWWHU\

6WHHULQJVHUYR

7KURWWOHVHUYR

Do not use the S.BUS2 port

in SR mode.

It cannot use the telemetry.

,WFRQQHFWVZLWKSRUWZKLFKLVQRWXVHGك

:KHQDOOWKHSRUWVDUHXVHGFRQQHFW

DEDWWHU\XVLQJ+8%RU<KDUQHVV

%XLOWLQDQWHQQD

5HFHLYHUWRSLVFOHDQ

2XWVLGH$QWHQQD

&+

&+

6%86

&+

7HPSHUDWXUH

VHQVRU

530VHQVRU

9ROWDJHVHQVRU

7HOHPHWU\VHQVRUV

2SWLRQ

'RQWFXWRUEXQGOH

WKHUHFHLYHU

DQWHQQDZLUH

The Example of Connection

LED Indication

Compliance Information Statement (for U.S.A.)

This device, trade name Futaba Corporation, model number R334SBS, complies with part15 of the FCC Rules.

Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

To assure continued FCC compliance:

$Q\FKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHGE\WKHJUDQWHHRIWKLVGHYLFHFRXOGYRLGWKHXVHUVDXWKRULW\

to operate the equipment.

2. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

In case of T-FHSSIn case of T-FHSS SR

FUTABA CORPORATION

Makuhari Techno-Garden Bldg. B-6F, 1-3 Nakase, Mihama-ku, Chiba, 261-8555, Japan

Phone: +81-43-296-8259, Facsimile: +81-43-296-8253

Futaba R334SBS Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info