Bedienungsanleitung Futaba R6106HFC (Seite 1 von 1) (Englisch)

747954

Zoom out

Zoom in

Vorherige Seite

1/1

Nächste Seite

Usage condition on "High

Speed mode"

ｎ

CAUTION

ｊ

The "High Speed mode"

accept the digital servos only

or most type of peripherals.

s)FANYANALOGSERVOSCONNECTEDTOTHESE

output as it will cause malfunction.

Please check the peripherals if there's

any malfunction with whole stick lever

THROW )F ANYMALFUNCTIONOCCURPLEASE

change the operation mode to "Normal

mode."

R6106HF

For parkﬂight or indoor use airplanes.

For electric helicopters up to 1000mm of main rotor diameter.

R6106HFC

For small size airplanes such as wing span of up to around 1300mm.

For carbon fuse such as non powered sail planes.

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation of

America, model number R6106HF/R6106HFC,

complies with part15 of the FCC Rules. Operation is

subject to the following two conditions:

(1)

This device may not cause harmful interference, and

(2) This device must accept any interference

received, including interference that may cause

undesiredoperation.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

TEL (217)398-0007 or E-mail: service@futaba-rc.com (Service)

R6106HF/R6106HFC Speciﬁcations

FASST-2.4GHz system 6-channel receiver

• Power requirement: 3.3V~8.5V regulated output

from ESC, etc. (*1)

• Battery F/S voltage: 3.8V

•

Size: 0.85 x 1.53 x 0.48 in. (21.7 x 38.8 x 12.3 mm)

• Weight: 0.24 oz. (6.7g)/0.25 oz. (7.1g)

(*1) Be sure that when using ESC's regulated output

the capacity of the ESC must meet your usage

condition.

Re-adjust the F/S position (only

for TM-7/TM-8)

Press and hold the Link/Mode switch

between one(1) and two(2) seconds.

0 to 1 sec. 1 to 2 sec. More than 2 sec.

0 sec. 1 sec. 2 sec.

Press and Hold time

No function

With TM-7, TM-8

To set the F/S

position(No re-link)

Re-link(ID set) and to

set the F/S position

No function

With TM-10, TM-14,

6EX, 7C, etc.

Re-link(ID set)

FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan

-. ©&54!"!#/20/2!4)/.

Operation Mode Select

The operation mode is on "Normal mode" from

factory shipping. When to change the mode,

please follow the steps shown below.

Turn off the receiver.

Press and hold the link/mode switch and

turn on the receiver. Keep the switch hold

more than one(1) second. The LED starts

ﬂashing with the current status.

Release the switch.

Turn off the receiver.

By doing this step, the mode can switch over

between two(2) modes.

0 to 1 sec. More than 1 sec.

0 sec. 1 sec.

Press and Hold time

Turn on the receiver.

No function

Showing the CURRENT

mode with blink.

Red Blink = Normal

Green/Red Blink =

High Speed

Solid as the mode changed.

Red Solid = Normal

Green/Red Solid = High

Speed

(Become Red after one (1)

second)

㧔Function㧕

To change the mode between

Normal and High Speed

㧔LED

Status㧕

Please check the operation mode by observing

the LED when turning on the receiver. If possible

there's no FASST transmitter turned on around you

in order to make ﬁrmer check.

When turn on the receiver, the LED will be;

s2EDWHENON.ORMALMODE

s'REENAND2EDMAKES/RANGEWHENON(IGH

3PEEDMODE!FTERTWOSECONDSCHANGETO2ED

If there are some FASST transmitter turned on

around the receiver, the LED may show the above

status for a brief moment then changed to the

status indication as shown in the "LED indication"

table.

LED Indication

'REEN Red Status

Solid Solid )NITIALIZING

Off Solid No signal reception

Solid Off Receiving signals

Blink Off 2ECEIVINGSIGNALSBUT)$ISUNMATCHED

Link to the transmitter

Press and hold the Link/Mode switch more

than two(2) seconds.

ｎ

WARNING

ｌ

Do not perform the linking procedure

with motor's main wire is connected

or the engine is operating as it may result in

serious injury.

ｊ

7HILETHELINKINGISDONEPLEASE

cycle receiver power and check if

the receiver to be linked is really under the

control by the transmitter to be linked.

Thank you for purchasing the

R6106HF

R6106HFC

FASST receiver. These models have

two(2) operation mode as shown below.

Normal mode/High Speed mode

The "Normal mode" accepts any type of servos

or the peripherals as the frame rate of the output

is 16ms. The "High Speed mode" only accept

the digital servos, including BLS series, and

most peripheral equipments such as the gyros or

brushless ESCs. The frame rate of the outputs is

8ms.

The

R6106HF

R6106HFC

are compatible with

the FASST transmitters as shown below.

T6EX-2.4GHz, T7C-2.4GHz, TM7,

T8FG-2.4GHz, TM8, T10CG-2.4GHz

TM10,

TM14 (on 7ch-mode)

LED

Link/Mode Switch

R6106HF

R6106HFC

LED

Link/Mode Switch

Antenna

Antenna installation for carbon fuse

(R6106HFC)

ｎ

WARNING

ｊ

4HEANTENNA PORTIONOFMMTIP

must be fully exposed.

s

Please make sure that the exposed portion won't

be slided back in the fuse by the wind pressure

or other force during the ﬂight session.

Usage precautions about the power source

We do not recommend to use the power source of less

THAN6BUTIFTOUSETHELOWERVOLTAGESOURCEPLEASE

keep in mind the condition shown below.

s&AIL3AFEFUNCTION-534BEINOFFSINCETHEBATTERYFSWILL

disturb the normal operation.

s0LEASEMAKESURETHATTHEFULLLOADEDCONDITIONOFTHE%3#

and the servos won't disturb the receiver operation before

start ﬂight.

This is very important since the receiver will stop operation

WHENTHESUPPLYVOLTAGEDROPSTOAROUND6

s0LEASE BE SURE THAT THE %3# OR SERVOS CAN KEEP mAWLESS

operation till such a lower voltage.

)FTHESERVOgSMAXIMUMVOLTAGERATINGISLESSTHAN6

the power source voltage must not exceed the servo's

rating.

Futaba R6106HFC Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info