Bedienungsanleitung Futaba R7008SB (Seite 1 von 2) (Englisch)

747960

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Applicable systems: Futaba FASSTest-2.4GHz

system transmitter

Compliance Information Statement (for U.S.A.)

This device, trade name Futaba Corporation of America, model number R7008SB, complies with part15 of the

FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation.

(3) This module meets the requirements for a mobile device that may be used at separation distances of more than

20cm from human body.

To meet the RF exposure requirements of the FCC this device shall not be co-located with another transmitting

device.

The responsible party of this device compliance is: Futaba Service Center 3002 N Apollo Drive Suite 1,

Champaign, IL 61822 U.S.A. TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

R7008SB Speciﬁcations

FASSTest-2.4GHz system(18CH/12CH mode)/

S.BUS2 and S.BUS port and 8 channels for conven-

tional system receiver

• Dual antenna diversity

• Size: 0.98 x 1.86 x 0.56 in. (24.9 x 47.3 x 14.3 mm)

• Weight: 0.38 oz. (10.9g)

• Power requirement: 3.7V to 7.4V(Voltage range: 3.5 to

8.4V)

• Battery F/S Voltage: It sets up with a transmitter

• Extra Voltage port: 0

∼

70V DC

* Be sure that when using ESCs regulated output the capacity of the

ESC must meet your usage condition.

LED Indication

Green Red Status

Off Solid No signal reception

Solid Off Receiving signals

Alternate blink Unrecoverable error (EEPROM, etc.)

(Antenna installation)

90˚

Please refer the table below for

LED status vs receiver's condition.

1M23N17491

＋

−

6%86

SRUW

6%86SRUW 6%ك

6%86ك

56%

7HUPLQDOER[

6%866HUYR

6%86*\UR

+8%

([WUD9ROWDJH

3RUW

/LQN0RGHVZLWFK

$QWHQQD

/('

6HUYRIRU FRQYHQWLRQDO

V\VWHP

&KDQQHORXWSXW

&KDQQHORXWSXW

7HPSHUDWXUH

6HQVRU

530

6HQVRU

9ROWDJH

6HQVRU

9ROWDJH

6HQVRU

$OWLWXGH

6HQVRU

$OWLWXGH

6HQVRU

6%867RRO

,WLVQRWXVHGIRUDOLQN

It connects with the

battery for power, etc.

External voltage input

cable of an option is

used. The voltage of

the battery can be

displayed with a

transmitter.

Usage precaution

• Analog servos cannot be used with the

R7008SB in the FASSTest 12CH mode.

• The R7008SB receiver can only be used

with FASSTest capable transmitters.

• Don't connect to Extra Voltage before turn-

ing on a receiver.

WARNING

Changes or modiﬁcation not expressly

approved by the party responsible for

compliance could void the user’s authority

to operate the equipment.

The R7008SB receiver should be protect-

ed from vibration by foam rubber, Velcro

or similar mounting methods. Protect

from moisture.

Keep away from conductive materials to

avoid short circuits.

Antenna installation precaution

Do not cut or bundle the receiver antenna

wire.

Do not bend the coaxial cable. It causes

damage.

The antennas must be mounted in such a

way to assure they are strain relieved.

Keep the antenna as far away from the motor,

ESC and other noise sources as you possibly can.

Be sure that the two antennas are placed at 90

degrees to each other.

• The R7008SB has two antennas. In order to maximize signal

reception and promote safe modeling Futaba has adopted a

diversity antenna system. This allows the receiver to obtain

RF signals on both antennas and ﬂy problem-free.

Antenna installation for carbon fuselage

WARNING

You must leave 30mm at the tip of the antenna

fully exposed. The exposed antenna should be

secured so that it cannot move around or back

inside of your aircraft.

S.BUS2 precaution

DANGER

Don't connect a connec-

tor, as shown in a before

ﬁgure.

• It will short-circuit, if it connected

in this way. A short circuit across

the battery terminals may cause

abnormal heating, ﬁre and burns.

WARNING

Only S.BUS2 capable devices may be connected

to the S.BUS2 port. Standard S.BUS servos and

gyros should not be connected to the S.BUS2 port.

(Typical installation)

FASSTest-2.4GHz Bidirectional

Communication System

S.BUS2 / S.BUS Port and 8 Channels for

Conventional System

Receiver

R7008SB

Thank you for purchasing a Futaba R7008SB FASSTest-

2.4GHz compatible receiver. The R7008SB receiver features bi-

directional communication with a FASSTest Futaba transmitter

using the S.BUS2 port. Using the S.BUS2 port an impressive

array of telemetry sensors may be utilized. It also includes both

standard PWM output ports and S.BUS output ports.

S.BUS2

5HFHLYHU

Do not insert either a switch

or battery in this manner.

DANGER

Instruction Manual

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba R7008SB Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info