Bedienungsanleitung Futaba R7008SB (Seite 2 von 2) (Englisch)

747960

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

WARNING

Do not perform the linking procedure while the

motor's main wire connected or the engine is

operating as it may result in serious injury.

When the linking is complete, please cycle

the receiver power and ensure the receiver is

properly linked to the transmitter.

Please power up your system in this order.

Transmitter ﬁrst, followed by the receiver.

If the R7008SB receiver was previously linked to

another transmitter, make sure that transmitter

is not operating while linking the receiver to the new

transmitter.

FUTABA CORPORATION

1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba-ken, 299-4395, Japan

Phone: +81 475 32 6982, Facsimile: +81 475 32 6983

Link to the transmitter

Easy Link ID allows FASSTest receivers to link

to compatible transmitter without pressing the

link button on the receiver.

Bring the transmitter and the receiver

close to each other, within 20 inches (half

meter).

Turn on the transmitter. Place the

transmitter into the receiver linking mode.

Turn on the receiver.

The receiver will wait for the linking

process to begin for 2 seconds. Following

that it will return to the normal operation

mode.

When the LED of the receiver changes

from blinking red to solid green, linking is

complete.

(A link waiting state is ended in 1 second.)

• Refer to the transmitters operation manual for complete details on how to place the transmitter into the linking mode.

• If there are many FASSTest systems turned on in close proximity, your receiver might have difﬁculty establishing a link to

your transmitter. This is a rare occurrence. However, should another FASSTest transmitter/receiver be linking at the same

time, your receiver could link to the wrong transmitter. This is very dangerous if you do not notice this situation. In order

to avoid the problem,we strongly recommend you to double check whether your receiver is really under control by your

transmitter.

• If the System Type of the transmitter is changed, the receiver will need to be re-linked to the transmitter.

Channel Modes

The R7008SB is capable of changing its channel allocations as described in the table below. This is

especially important when using the receiver in a dual receiver mode. See your transmitter operation

manual for complete details on operating in the dual receiver mode.

Press and hold down the Link/Mode

button on the R7008SB receiver.

Turn the receiver on while holding down

the Link/Mode button. After power up, the

button can be released.

The LED should now be blinking red in

one of the patterns described by the chart

below.

Each press of the Mode/Link button

advances the receiver to the next mode.

When you reach the mode that you wish

to operate in, press and hold the Mode/

Link button for more than 2 seconds.

Once locked into the correct mode the

LED will change to a solid color.

Please cycle the receiver(s) power off and

back on again after changing the Channel

Mode.

FASSTest

FASSTest is a bidirectional communication system

between the R7008SB receiver and FASSTest capable

transmitters. Multiple optional telemetry sensors may

be connected to the S.BUS2 on the receiver and that

data is in turn displayed on the transmitter.

*Please see your transmitters operation manual

to configure transmitter to operate with telemetry

sensors.

S.BUS2

S.BUS2 extends S.BUS and supports bidirectional

communication. Sensors are connected to the

S.BUS2 port.

*Only S.BUS2 capable devices may be connected

to the S.BUS2 port. Standard S.BUS servos and

gyros should not be connected to the S.BUS2

port.

Output

connector

Channel

Mode Ａ

1 ∼ 8CH

Mode B

1 ∼ 7CH

Mode C

9 ∼ 16CH

Mode D

9 ∼ 15CH

11199

2221010

3331111

4441212

5551313

6661414

7/B 7 7 15 15

8/SB 8 S.BUS 16 S.BUS

Red LED

blink

1 time 2 time 3 time 4 time

R7008SB CH Mode table

WARNING

Turn on the power in transmitter → receiver order. In addition, always check the operation

of all the servos before ﬂight.

Do not insert or remove the servo connector while the receiver power is ON.

Since the S.BUS servo switches the operation mode automatically according to the type of signal

(S.BUS signal/PWM signal) from the receiver, if the connector is inserted or removed while the power is

ON, an S.BUS connected servo will be erroneously recognized and may stop.

S.BUS hub S.BUS hub

S.BUS output

S.BUS

Ch output/

Battery terminal

R2008SB

Battery

S.BUS servo

Conventional

servo

2ch 4ch

3ch 5ch

6ch

What is S.BUS?

* Set the channel of

S.BUS

servos by using an

SBC-1

channel changer,

CIU-2

USB serial inter-

face or the programming software resident in the

18MZ

transmitter.

Can also be used together with conventional

servos. However, conventional servos cannot be

used by the S.BUS output.

When using servos with a remote battery pack,

use S.BUS Hub with Cable (2-way/remote bat-

tery pack use).

Please refer to the instruction manual of S.BUS

Hub with Cable (2-way/remote battery pack use)

for the connection method.

[Connection by S.BUS system]

Unlike conventional radio control systems, the

S.BUS system uses data communication to transmit

control signals from a receiver to a servo, gyro, or

other S.BUS compatible device. This data includes

commands such as “move the channel 3 servo to 15

degrees, move the channel 5 servo to 30 degrees”

to multiple devices. The S.BUS devices execute

only those commands for their own set channel. For

this reason, it can be used by connecting multiple

servos to the same signal line.

Futaba R7008SB Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info