Bedienungsanleitung Futaba R7018SB (Seite 1 von 5) (Englisch)

747962

Zoom out

Zoom in

Vorherige Seite

1/5

Nächste Seite

R7018SB

●

Applicable systems: Futaba FASSTest-2.4GHz / FASST-Multi-ch system transmitter

The R7018SB has a Dual Battery System. Multiple servos can be driven by connecting 2 large capacity batteries. Even if the voltage

RIRQHEDWWHU\GURSVWKHRWKHUEDWWHU\DOORZVVDIHÀLJKW7KHR7018SB can also be switched the FASST-Multi-ch System.

◆

FASSTest-2.4GHz Bidirectional Communication System / FASST-Multi-ch 2.4GHz

◆

Dual Battery

◆

S.BUS2 / S.BUS Port and 18 Channels for Conventional System Receiver

1M23N30102

CONTENTS

ESC ( motor controller) that supplies power

from the drive battery (BEC- Battery Eliminator

Circuit) to the receiver cannot be used.

Ordinary switches

(SSW-J, HSW-J, HSW-L,

etc.) cannot be used.

Usage precaution

• Analog servos cannot be used with the R7018SB in the

FASSTest 12CH mode.

• When the FASST Multi-ch High-speed Mode is used, analog

servos cannot be used at the CH1

∼

6 outputs for convention

systems. However, in other than the FASSTest 12CH mode,

analog servos can be used at CH7

∼

16, DG1 and DG2 at

any time.

• Don't connect to Extra Voltage Telemetry Port before turning

on a receiver.

WARNING

Changes or modiﬁcation not especially approved by the party

responsible for compliance could void the user s authority to

operate the equipment.

When the model is not being used, always remove or

disconnect the battery.

■ When the switch is off, a slight amount of current still flows. Unless the

switch and battery are disconnected, the battery will be damaged from

excessive discharge.

The R7018SB receiver should be protected from vibration by

foam rubber, Velcro, or similar mounting methods. Protect from

moisture.

Keep away from conductive materials to avoid short circuits.

When only one battery is connected, always insulate the

unused connector.

Antenna installation precaution

Do not cut or bundle the receiver antenna wire.

Do not bend the coaxial cable. It causes damage.

The antennas must be mounted in such a way to assure they

are strain relieved.

Keep the antenna as far away from the motor, ESC and other

noise sources as you possibly can.

Be sure that the two antennas are placed at 90 degrees to each

other.

■ The R7018SB has two antennas. In order to maximize signal

reception and promote safe modeling Futaba has adopted a diversity

antenna system. This allows the receiver to obtain RF signals on both

antennas and fly problem-free.

Antenna installation for carbon fuselage

You must leave 30mm at the tip of the antenna fully exposed.

The exposed antenna should be secured so that it cannot move

around or back inside of your aircraft.

Be careful of connector insertion

Don't connect an S.BUS servo / gyro to S.BUS2 connector.

Do not connect the power supply battery to other than the

power supply connector.

■ There is the danger of ignition, explosion, or burning.

Link precaution

Do not perform the linking procedure while the motor's main

power connected or the engine is operating as it may result in

serious injury.

When the linking is complete, please cycle the receiver power

and ensure the receiver is properly linked to the transmitter.

Please power up your system in this order. Transmitter ﬁrst,

followed by the receiver.

If the R7018SB receiver was previously linked to another

transmitter, make sure that transmitter is not operating while

linking the receiver to the new transmitter.

56% ¼ 

([FOXVLYHVZLWFK ¼ 

0LQLGULYHU ¼ 

)HPDOH'HDQV

8OWUD3OXJ ¼ 

+HDWVKULQNWXEH

/LQN0RGH

VZLWFK

%DWWHU\FRQQHFWRU

'HDQV8OWUD3OXJ

$QWHQQD

0RGH/('

/LQN/('

%DWWHU\%/('

%DWWHU\$/('

Use a Deans Ultra Plug with

the R7018SB power supply

battery. Batteries of this

connector cannot be used.

([WUD9ROWDJH

7HOHPHWU\3RUW

Thank you for purchasing a Futaba R7018SB FASSTest-2.4GHz compatible receiver.

The R7018SB receiver features bi-directional

communication with a FASSTest Futaba transmitter using the S.BUS2 port. Using the S.BUS2 port an impressive array of telemetry

sensors may be utilized. It also includes both standard PWM output ports and S.BUS output ports.

Compliance Information Statement

(for U.S.A.)

This device, trade name Futaba Corporation, model number R7018SB,

complies with part15 of the FCC Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference

that may cause undesired operation.

(3) This module meets the requirements for a mobile device that may be used

at separation distances of more than 20cm from human body.

To meet the RF exposure requirements of the FCC this device shall not be co-

located with another transmitting device.

The responsible party of this device compliance is:

Futaba Service Center

3002 N Apollo Drive Suite 1, Champaign, IL 61822 U.S.A.

TEL (217)398-8970 or E-mail: support@futaba-rc.com (Support)

- 1 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba R7018SB Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Futaba R7018SB

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info