Bedienungsanleitung Futaba T-16IZ (Seite 115 von 228) (Englisch)

747917

115

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

115

→ GO to TABLE OF CONTENTS

Trainer

Trainer system starting and setting

T16IZ trainer system makes it possible for the

instructor to choose which channels and operation

modes can be used in the student's transmitter.

The function and rate of each channel can be set.

The training method can also be matched to the

student's skill level. Two transmitters must be

connected by an optional Trainer Cord, and the

Instructor's transmitter should be programmed for

trainer operation, as described below.

When the Instructor activates the trainer switch, the

student has control of the aircraft (if MIX/ FUNC/

NORM mode is turned on, the Instructor can make

corrections while the student has control). When

the switch is released the Instructor regains control.

This is very useful if the student gets the aircraft

into an undesirable situation.

● Setting data are stored to model data.

● Student rate can be adjusted at MIX/FUNC/

NORM mode.

● Activated student channels can be selected

by switches.

Note: This trainer system can be used in the following

manner:

1. With the T16IZ transmitter and a conventional

transmitter, if the channel order is different, it is

necessary to match the channel order before using this

function.

You can select the channel of input data from student's

transmitter in the "FUNC" or "MIX" mode.

2. When the T16IZ is used as the instructor’s transmitter,

set the modulation mode of the student’s transmitter to

PPM.

If being used as the student, T16IZ can be connected to

the instructor's transmitter which requires the student's

mode to be PPM. T16IZ always sends PPM mode signal

from the trainer jack.

(In the case of student's transmitters other than 2.4 GHz)

3. Be sure that all channels work correctly in both

transmitters before ying.

Correspondingtypesoftransmittersandtrainermodesettings:

Types of transmitters

Instructor's transmitter settings Student's transmitter settings

System Type Trainer setting System Type Trainer setting Trainer Cords

Instructor Student Mod. mode CH mode Mod. mode CH mode Mod. mode

T16IZ,FX-32

T14SG,T16SZ,

T18SZ,T18MZ,

T32MZ

T16IZ,FX-32

T14SG,T16SZ,

T18SZ,T18MZ,

T32MZ

Arbitrary 16CH Arbitrary 16CH -

T12FG and 9C

Trainer Cords

T16IZ

T14MZ, FX-40, T12Z,

T12FG,

FX-30

Arbitrary 12CH

PCM-G3

2.4G

12CH PPM

T16IZ T8FG, FX-20 Arbitrary

12CH FASST-MLT2

- -

8CH FASST-MULT

T16IZ

T10C, T9C,

T7C,T6EX, T4EX

Arbitrary 8CH PPM - - T12FG

T16IZ T10CG,T7C Arbitrary 8CH Arbitrary - - T12FG

T16IZ

T10J, T8J, T6K, T6J,

T6L

Arbitrary 8CH Arbitrary - -

T12FG and 9C

Trainer Cords

T14MZ, FX-40, T12Z,

T12FG,

FX-30

T16IZ Arbitrary 12CH Arbitrary 12CH -

T8FG, FX-20 T16IZ Arbitrary 12CH Arbitrary 12CH -

T10C, T10CG, T10J,

T9C, T7C

T7C, T8J, T6K

T6J

T16IZ Arbitrary - Arbitrary 8CH -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-16IZ Seite 115

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info