Bedienungsanleitung Futaba T-16IZ (Seite 121 von 228) (Englisch)

747917

121

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

121

→ GO to TABLE OF CONTENTS

The dedicated mixes, etc. usable when airplane

or glider model type is selected are displayed

in this Model menu functions section. First use

the Model type function of the Linkage menu to

preset the model type, wing type, and tail type

matched to the fuselage used. Other settings reset

the data used in mixing function, etc.

These dedicated mixes can be set for each

flight condition, as required. When you want to

use the system by switching the settings for each

condition by switch or stick position, use the

Condition select function to add ight conditions.

(Up to 8 conditions can be used)

Note: The T16IZ is designed so that the airplane and

glider model types can handle aircraft of the same

wing type.

The functions common to airplanes and gliders,

except some dedicated functions, are summarized

without regard to the model type.

The setting items are different, depending on the

number of servos, etc. according to the wing type

used. The setup screens in the instruction manual

are typical examples.

MODEL MENU (Airplane/Glider functions)

Model menu (Airplane/Glider) functions table

Servomonitor

Displays the servo test and operation position

Conditionselect

Flight conditions addition, deletion, copy, condition renaming, and condition

delay can be set.

AFR

Sets the angle and curve of all the operation functions.

Dualrate

D/R curve which can be switched with a switch, etc. can also be added.

Program.mixes

Program mixing which can be freely customized. Up to 10 mixes can be used for

each condition.

Ailerondi󰮏erential

This function adjusts the left and right ailerons. Roll axis correction and fine

tuning with a VR are also possible. This is convenient when making settings

during ight.

[Airplane/glider, 2 ailerons or more]

Flapsetting

The aps can be adjusted independently. For a 4 aps model, the camber aps

can be mixed with the brake aps.

[Airplane/glider, 2 aps or more]

AIL →Camberap

This mix operates the camber flaps in the aileron mode. It improves the

operation characteristic of the roll axis.

[Airplane/glider, 2 ailerons + 2 aps or more]

AIL →Brakeap

This mix operates the brake aps in the aileron mode. It improves the operation

characteristic of the roll axis.

[Airplane/glider, 4 aps or more]

Aileron →Rudder

This mix is used when you want to operate the rudder at aileron operation.

Banking at a shallow bank angle is possible.

[Airplane/glider, general]

Elevator → Camber

This mix is used when you want to the mix camber aps with elevator operation.

Lifting force can be increased at elevators up.

[Airplane/glider, 2 ailerons or more]

Cambermixing

This mix adjusts the camber and corrects the elevators. [Airplane/glider, 2 ailerons or more]

Airbrake →ELE

This mix is used to correct operation of the airbrakes (spoilers) when landing.

[Airplane/glider, general]

Camberap → ELE

This mix is used to correct for attitude changes when the camber aps are being

used.

[Airplane/glider, 2 ailerons + 1 ap or more]

Rudder → Aileron

This function is used to correct roll knife edge, etc. of stunt planes. [Airplane/glider, general]

Rudder → Elevator

This function is used to correct roll maneuvers, knife edge, etc. of stunt planes. [Airplane, general]

Buttery(Crow)

This function is used when powerful brake operation is necessary. [Glider, 2 ailerons or more]

Trimmix1/2

The ailerons, elevators, and flaps trim offset rate can be called by switch or

condition selection.

[Glider general]

Snaproll

This function selects the snap roll switch and adjusts the steering angle of each

rudder. Servo speed can also be adjusted.

[Airplane general]

Airbrake

This function is used when airbrakes are necessary when landing or when diving,

etc. during ight.

[Airplane, general]

Gyro

This is a dedicated mix when a GYA Series gyro is used. [Airplane/glider/multicopter, general]

Ailevator

This function adjusts the elevators and ailerons of models with elevator

specications.

[Airplane/glider, elevator specications]

Acceleration

Allows a brief "overload" in response to sudden Elevator, Elevator → Camber,

and Ail → Rudder.

[Airplane/glider general]

Motor

The operation speed when the motor of F5B and other EP gliders is started by

switch can be set.

[Airplane/glider, general]

V-Tail

This function adjusts the elevators and rudder of V-tail models. [Airplane/glider, V-tail specications]

Winglet

This function adjusts the left and right rudders of winglet models. [Airplane/glider, winglet specications]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-16IZ Seite 121

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info