Bedienungsanleitung Futaba T-16IZ (Seite 181 von 228) (Englisch)

747917

181

Zoom out

Zoom in

Vorherige Seite

1/228

Nächste Seite

181

→ GO to TABLE OF CONTENTS

S.BUSBasicMenuS.BUSBasicMenu

The channel of each function

can be changed.

This resets the S.BUS channel assign-

ments back to the defaults.

The

SBUS BASIC

screen is accessed via the

BASIC MENU

screen. Set the CH for each function according to the transmitter to be used.

Any unused functions should be set to INH (Inhibited). For example, if the Gain A/E and Gain RUD remote gain functions are not going to

be used, then set them to [INH]. The CGY760R/CGY755 will then allow you to make gain adjustments within the respective menu.

WARNING

Always verify that the S.BUS function as-

signments match your transmitter’s function

(in the FUNCTION menu) assignments. If any

changes are made within the transmitter func-

tion assignments, then it will also be neces-

sary to make the changes within the S.BUS

function assignments. To change the channel,

CGY and T16IZ must be connected.

ELE2 channel Servo Type

(If you want to use the ELE2 port for purposes other than swash.)

This selects the ELE2 servo types. There are three types of the servo

driving frequency selection, AN:70

Hz, DG285

Hz, and 760

μS. All Futaba

digital servos can be operated with fastest DG:285

Hz mode but some

of other brands of servos do not support DG:285

Hz mode. In this case,

select the proper servo driving frequency per the manufacturer’s speciﬁ-

cations.

If you select H4-00 or H4-45 with 4 servo swashes, cannot set this ELE2

port servo type. In that case, select all swash servo types in SWH basic

servo type.

Setting:AN:70



Hz/DG:760



μS/DG:285



Hz　Initialsetting:DG:285



WARNING

The servo type parameter within the CGY must match the type of

servo you are using. Incorrect setting may damage the CGY or the

servo. Incorrect setting may also result in a loss of control during

ﬂight.

S. BUS connection: Condition on change channel

Using the methodology described previously, determine the "Cond CH #" and

set the condition change channel of the transmitter. In this example, DG1 is the

conditional change channel.

As with the ﬂight condition function of the transmitter, it is possible to utilize

pre-determined settings, each activated by a switch or switches on the

transmitter. By setting the condition switch on the channel with the AFR

function of the transmitter and setting the point for each ﬂight condition with

the AFR point curve, you can switch the condition of CGY760R/CGY755 in

conjunction with the ﬂight condition switch of the transmitter.

Wireless channel

The wireless channel uses two consecutive channels. For example, if CH13

is set to "# 1", CH14 is automatically set to "# 2". Therefore, when using this

function, two consecutive free channels are required for the transmitter. It is not

possible to use a channel assign that is used for another function.

CAUTION

Be sure to check the operation for all conditions 1 to 5 before ﬂying.

The setting of "wireless CH" is possible only when the transmitter

and the CGY are powered off and the CGY is turned on.

Be sure to connect and disconnect the CGY and T16IZ connection cable

with the power off.

2 consecutive free channels

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Futaba T-16IZ Seite 181

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info